Samsung ED40D Quick Setup Manual

Quick Setup Guide
ED32D ED40D ED46D ED55D
- The colour and the appearance may differ depending on the product, and the specifications
are subject to change without prior notice to improve the performance.
- Recommended hours of use per day of this product is under 16 hours.
If the product is used for longer than 16 hours a day, the warranty may be void.
- Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing
LLC in the United States and other countries.
Checking the Components
- Contact the vendor where you purchased the product if any
components are missing.
- The appearance of the components may differ from the images
shown.
Warranty card
Quick Setup Guide
(Not available in some locations)
D-SUB cable Power cord
Batteries
Remote Control
(Not available in some locations)
RS232C(IN) adapter
EDD32~55-India-QSG_BN68-05831S-00.indd 1
BN68-05831S-00
Remote Control
1
3
2
4
Display or hide the onscreen display menu, or return to the
1
previous menu.
Move to the upper, lower, left or right menu, or adjust an option's
2
setting.
Confirm a menu selection.
3
Exit the current menu.
4
Reverse Side
Port Description
HDMI IN Connects to a source device using an HDMI cable.
SERVICE (5V 0.5A) This port is used to upgrade the software.
RGB IN Connects to a source device using a D-SUB cable.
DVI IN Connects to a source device using a DVI cable or HDMI-DVI cable.
AUDIO OUT Connects to the audio of a source device.
RGB / DVI / HDMI / AV /
Connect to audio input using an audio cable.
COMPONENT AUDIO IN
RS232C IN Connects to MDC using an RS232C-stereo adapter.
- For details on how to use the MDC programme, refer to Help after installing the programme. The MDC programme is available
RS232C OUT on the website.
COMPONENT / AV IN Connects to a source device using the Component/AV cable.
Remote Sensor To control the remote control in front of the product, lower the remote control sensor in the direction of the arrow.
Troubleshooting Guide
Issues Solutions
The screen keeps Check the cable connection between the
switching on and off. product and PC, and ensure the connection is
secure.
No Signal is displayed Check that the product is connected correctly
on the screen. with a cable.
Check that the device connected to the
product is powered on.
Not Optimum Mode is
This message is displayed when a signal
displayed. from the graphics card exceeds the product's
maximum resolution and frequency.
Refer to the Standard Signal Mode Table and
set the maximum resolution and frequency
according to the product specifications.
The images on the
Check the cable connection to the product.
screen look distorted.
Adjust Coarse and Fine.
The screen is not clear.
The screen is blurry.
Remove any accessories (video extension
cable, etc) and try again.
Set the resolution and frequency to the
recommended level.
The screen appears Check that the resolution and frequency of the
unstable and shaky. PC and graphics card are set within a range
compatible with the product. Then, change the
There are shadows or
screen settings if required by referring to the
ghost images left on the
Additional Information on the product menu
screen.
and the Standard Signal Mode Table.
Remote Sensor
Issues Solutions
The screen is too bright.
Adjust Brightness and Contrast.
The screen is too dark.
Screen colour is Go to Picture and adjust the Colour Space
inconsistent. settings.
White does not really Go to Picture and adjust the White Balance
look white. settings.
There is no sound. Check the connection of the audio cable or
adjust the volume.
Check the volume.
The volume is too low. Adjust the volume.
If the volume is still low after turning it up to
the maximum level, adjust the volume on
your PC sound card or software programme.
The remote control does Make sure that the batteries are correctly in
not work. place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs
switched on in the vicinity.
2015-11-27 4:32:59