Related Manuals for Megaman Connect JSJSLW450
Summary of Contents for Megaman Connect JSJSLW450
- Page 1 2-Way Dimmer (1 Gang) Model No. JSJSLW450 Instruction Manual Connect Series www.lightwaverf.house Version 2...
- Page 2 EC DECLARATION OF CONFORMITY Responsible Authority: LightwaveRF PLC, Innovation Campus Birmingham Faraday Wharf Holt Street Birmingham B7 4BB Tel: +44 (0)121 250 3625 Email: enquiries@lightwaverf.com Model Number(s): JSJSLW450 Description: 2-Way Dimmer Directives this equipment Complies with: 2006/95/EC The Low Voltage Directive N/A 2004/108/EEC The Electromagnetic Compatibility Directive 1999/5/EC R&TTE Directive 93/68/EEC CE Marking Directive...
-
Page 3: Get Started
Get Started How do I get started? Please refer to the following installation and setup instructions. This will guide you, step by step, through the installation and setup process. What do I need? To install the Dimmer, you will need to remove and replace the existing lightswitch. -
Page 4: Installation
Installation Overview Amber LED. ‘On’ button. When illuminated, Hold to raise light level. the dimmer is o . Blue LED. When ‘O ’ button. illuminated, the Hold to decrease dimmer is on. light level. IMPORTANT: All LightwaveRF products can be legally DIY installed in your own home;... - Page 5 Quick Setup Guide Live in Switched live (live out) Screw 2-Way mounting hole switching connection IMPORTANT: If conducting an insulation resistance test, all LightwaveRF products must be disconnected from the mains, or damage will occur.
- Page 6 Quick Start Guide Installation VERY IMPORTANT • A LightwaveRF 2-Way Dimmer needs to be used in conjunction with a standard LightwaveRF Dimmer to perform 2-Way Switching. The LightwaveRF 2-Way Dimmer cannot be used in conjunction with a standard lightswitch. This will cause damage to the Dimmer. •...
- Page 7 Installation IMPORTANT: Turn o the mains electrical supply. Ensure that the wall (back) box has a minimum depth of 35mm. Remove and disconnect the existing lightswitch (if applicable). It may be useful at this point to mark out or take a photograph of the connections to the existing switch so that the correct wires can easily be transferred to the new dimmer.
- Page 8 Installation Connect the wiring as per the wiring diagram on the following page. Ensure that the terminals are properly tightened and that no bare wire is visible. Be aware that existing wiring circuits are not always correctly coloured, and that there may be other wired connections present in the back box;...
- Page 9 Installation From lighting circuit IMPORTANT: The signal cable input marked ‘S’ must ONLY be connected Live to the wire running to the other Switched live dimmer NOT live mains; this will 3 - C o re cause irreparable damage. cable Earth Live Signal cable...
- Page 10 Installation Replace the plate – a ‘click’ sound should be heard to signify that the plate has been correctly replaced. Important things to Consider • Wattage ratings for the Dimmers are per gang. The maximum circuit load for each 2-Way Dimmer Gang is equal to the maximum load on the standard LightwaveRF Dimmer it is connected to (i.e.
- Page 11 Compatibility & Lamps Compatibility Ensuring the compatibility of your lamps (bulbs) with LightwaveRF Dimmers will ensure that you get the best experience from your lighting setup. LightwaveRF dimmers are compatible with the following: • Selected dimmable LED lamps (see www.lightwaverf.house for further guidance and information).
-
Page 12: Manual Operation
Manual Operation Manual operation Manual dimming • Tap the ‘on’ (top) button once to switch the dimmer on (blue LED indicator will illuminate). Press and hold the ‘on’ button to raise the light level. • Tap the ‘o ’ (bottom) button once to switch the dimmer o (amber LED indicator will illuminate). -
Page 13: Troubleshooting
Troubleshooting Problem: The 2-Way Dimmer will not operate the lights and the LEDs on the Dimmer do not light up. Solution: Firstly, check that there is power to the dimmer. Make sure that the connected lamps (bulbs) are functioning correctly; the dimmer switch will not run unless it has a functioning lamp/s to complete the circuit. - Page 14 Troubleshooting Problem: The LED/CFL lamps that I am using flash / do not dim properly. Solution: Ensure that the lamps being used are dimmable; non dimmable lamps are not compatible with LightwaveRF dimmers. If the problem persists, the LED/CFL lamps may not be compatible with the dimmers; please contact technical help (via www.lightwaverf.com) for further advice.
- Page 15 FAQs Can I link the 2-Way Dimmer to a LightwaveRF controller? No. The 2-Way Dimmer is designed to take wired commands directly from the standard Dimmer that it is connected to. It does not contain an RF module and will not enter linking mode. How do I know that the dimmer switch will fit? The Dimmer is the same size as a standard lightswitch - it will fit all back boxes (standard lightswitch housing) over 35mm deep.
- Page 16 FAQs Can I use non dimmable lamps (bulbs) if I don’t dim them? No. The lamps must be dimmable even if they are not dimmed; the technology in the lamp must be compatible with that of the dimmer. What if I need a switch to operate on/o only? A LightwaveRF Relay in conjunction with a Wire-free Switch can be used for on/o switching in place of the dimmer (see www.lightwaverf.com).
-
Page 17: Technical Specification
Technical Specification Specification Input rating: 220-240V~ 50Hz. Back Box Depth: 35mm min. Earthing Requirement: Not essential (double insulated) Standby Energy Use: Less than 1W Wiring: Neutral wire NOT required Warranty: 2 year standard warranty... - Page 18 Version 2 2 Quadrant Park Mundells Welwyn Garden City Herts AL7 1FS 01707 386035 www.lightwaverf.house...
Need help?
Do you have a question about the Connect JSJSLW450 and is the answer not in the manual?
Questions and answers