Page 2
Contents are subject to revision without prior notice. PLANET is a registered trademark of BEWARD Co., Ltd All other trademarks belong to their respective owners. Energy Saving Note of the Device This power required device does not support Standby mode operation.
Table Of Contents 1. Introduction 1.1 Checklist Check the contents of your package for the following parts: z ST-810HP x 1 1. Introduction ....................5 z User's Manual x 1 1.1 Checklist ..................... 5 z Power Cord x 1 1.2 Product Description ................5 z Two 19”...
8-Port 10/100Mbps Fast Ethernet Switch LED indicators for system power, per port PoE ready and PoE activity, speed, 8-Port supports 48V DC power to PoE Powered Device (ST-810P) Link / Act 8-Port supports 56V DC power to PoE Powered Device (ST-810HP) ...
2. Hardware Description AC 100~240V, 50/60Hz, AC 100~240V, 50/60Hz, Power Requirements 2A max. 2.5A max. This product provides three different running speeds – 10Mbps and 100Mbps at Power Consumption 130 watts / 443BTU port 1 to port 8, 10/100/1000Mbps at port 9 and automatically distinguishes the speed of incoming connection.
The rear panel of the PoE Ethernet Switch indicates an AC inlet power socket, automatically supports 1000Base-T, 100Base-TX and 10Base-T networks. Users which accepts input power from 100 to 240V AC, 50-60Hz, 2A (ST-810P) or 100 to only need to plug a working network device into the 10/100/1000Base-T port, and 240V AC, 50-60Hz, 2.5A (ST-810HP).
Step 4: Connect your PoE Ethernet Switch to 802.3af / 802.3at complied Powered Port Type Cable Type Connector Devices (PD) and other network devices. 10Base-T Cat 3, 4, 5, 2-pair RJ-45 A. Connect one end of a standard network cable to the 10/100RJ-45 100Base-TX Cat.5 UTP, 2-pair RJ-45...
Perfect Combination 8-Port PoE Switch + 8-Ch NVR Step 3: Secure the brackets tightly. Step 4: Follow the same steps to attach the second bracket to the opposite side. 8 PoE IP Cameras Step 5: After the brackets are attached to the PoE Ethernet Switch, use suitable screws to securely attach the brackets to the rack, as shown in Figure 2-7.
2.5.2 IP Office Department / Workgroup PoE Switch 2.6 Power over Ethernet Powered Device With the business office expansion, the additional telephones required could be 3~5 watts Voice over IP phones installed in less cost via the implementation of PoE IP Telephony system than that Enterprise can install POE VoIP Phone, ATA and other of the traditional circuit wiring telephony system.
3. Power over Ethernet Overview Powered Source Equipment (PSE) Power sourcing equipment (PSE) is a device such as a switch that provides What is PoE? (sources) power on the Ethernet cable. The maximum allowed continuous output power per cable in IEEE 802.3af is 15.40 W. A later specification, IEEE 802.3at, The PoE is an abbreviation of Power over Ethernet;...
What is the power output of each PoE port? Solution: ST-810P: each PoE port supports 48V DC, 350mA, max 15.4 watts power output. Detect and inject by the standard of IEEE 802.3af. ST-810HP: each PoE port supports 56V DC, 600mA, max 30 watts power...
Appendix: A Networking Connection A.3 10/100Mbps, 10/100Base-TX When connecting your PoE Ethernet Switch to another Fast Ethernet switch, a A.1 PoE RJ-45 Port Pin Assignments bridge or a hub and a straight or crossover cable are necessary. Each port of the Switch supports auto-MDI/MDI-X detection.
Page 13
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight cable and crossover cable connection: SIDE 1 SIDE 2 Straight Cable 1 = White/Orange 1 = White/Orange SIDE 1 2 = Orange 2 = Orange...