Operational reliability and functionality are no longer ensured if the device is modified or adapted. Gann Mess- u. Regeltechnik GmbH is not liable for any damage arising from such modifications or adaptations. The risk is borne by the user alone.
Measurements must not be carried out on metallic surfaces. Gann Mess- u. Regeltechnik GmbH accepts no liability for damage resulting from non-adherence to the operating instructions or by not taking proper care during transport, storage or operation of the device, even if this requirement for care is not specifically addressed in the operating instructions.
1 Introduction Description The data logger Klima 20 & Klima 30 enable the measurement of relative humidity and air temperature using the sensors, which are placed in the measuring head. It is also possible to measure the material temperature of materials by connecting a temperature sensor to the Klima 30.
Introduction Device layout and button assignment - Klima 20 Internal sensor LCD display Start-Stop-Button LED: red USB-Port Figure 1-1 Device layout and button assignment - Klima 20 Data logger Klima 20 / 30...
Page 8
Battery Status info Unit Measurement 2 Measurement 2 Figure 1-2 Display symbols Klima 20 Measurement 1 Shown in the upper part of the display; shows the actual temperature value measured by the internal sensor Unit measurement This sign informs about the currently selected measurement unit of reading 1 It is possible to switch between °C = Celsius, °F = Fahrenheit,...
Introduction Device layout and button assignment – Klima 30 Internal sensor LCD display LED: green/red Start-Stop-Button USB-Port Mode-Button & Connection for external temperature sensor Figure 1-3 Device layout and button assignment - Klima 30 Data logger Klima 20 / 30...
Mode „LOG“ or „STOP“ is displayed; „LOG“: data logger records; Status info „STOP“: no measurement values are recorded Battery indicator Current state of the battery External EXT = external temperature sensor is adapted; value is shown at temperature sensor measurement 2 Data logger Klima 20 / 30...
The same happens after pressing any button. USB-Port To configure the data logger Klima 20 / Klima 30, connect the computer with the data logger by using the USB-cable. Start the suitable GANN software dialog D+ and connect the data logger with the computer by using the USB cable MK 26.
The values are shown in the lower measurement display (measurement 2). AVG – average MIN – Minimum MAX – Maximum AUT – value value value automatic change The display switches in 2-second clock between the Avg-Min-Max values by using the AUT-Mode. Data logger Klima 20 / 30...
The LCD-display informs about two measurement values and it also informs about some status information. It is possible to switch the display off by using the GANN software dialog D+. If the display is switched off, you can prevent that unwanted information is not shown.
The LED indicator blinks green during the measurement interval (during the data logger is recording) (Klima 30) The LED indicator blinks red when a given limit is exceeded (Klima 20 & Klima 30) External temperature sensor (only Klima 30) It is possible to connect an external temperature sensor to the USB-port of the data logger Klima 30.
When a temperature sensor is connected (Klima 30): the times given halving. Using a measuring interval of 1 Minute: the times given halving. Using a measuring interval of 1 second: the battery life time is about 2 weeks. Data logger Klima 20 / 30...
Page 16
Specifications 3 Specifications Technical Data - Klima 20 & Klima 30 Klima 20 Klima 30 Internal temperatur: -30 to +60°C -30 to +70°C External temperature sensor: - - - - - - - - - - - -50 to +125°C...
Page 17
Application notes and equipment Storage conditions Data loggers Klima 20 and Klima 30 may only be stored in the packaging that is supplied by us (also available as accessory). We will not assume any liability for damages, caused by non-compliance, to a device or the sensor system that is used in it.
Page 18
Application notes and equipment 4.1.3 GANN Dialog Software D+ (Klima 20 & Klima 30 In the basic set of the data logger, the GANN software dialog D+ is contained, as well as the suitable cable MK 26. technical change and errors excepted...