Advertisement
Save This Manual
Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible.
Read this material before using this product. Failure to do so can result in serious injury.
SAVE THIS MANUAL.
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. | ||
Indicates a hazardous situation which, if not avoided, will result in death or serious injury. | ||
Indicates a hazardous situation which, if not avoided, could result in death or serious injury. | ||
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. | ||
NOTICE CAUTION | Addresses practices not related to personal injury. |
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SAVE THESE INSTRUCTIONS.
56213 Black 56408 White | |
Lamp | 60 SMD LEDs |
Battery Pack | 3.7 VDC, 1500 mAh Li-Ion Battery |
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
Note: For additional information regarding the parts listed in the following pages, refer to Parts List and Diagram.
Underside of Lamp
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
Before the Security Light can operate properly, the battery needs to be fully charged. To charge the battery:
The UNIT WILL NOT FUNCTION UNLESS: The Solar Panel is first charged for 3 DAYS OF FULL SUN with the SENSOR POWER OFF.
The Power Switch, located under the Battery Housing of the Lamp, has three settings:
AUTO: The Lamp will illuminate automatically when motion is detected by the Motion Sensor Head.
OFF: Center position is power off.
ON: The Lamp stay illuminated functioning as a normal light.
Underside of Motion Detector Head
The Security Light has 3 different Control Knobs on the underside of the Motion Detector Head. They control the Motion Detector Head's sensor. They are:
NOTE: After each adjustment, walk the detection area to verify the adjustment just made.
The SENS Adjusting Knob sets the level of sensitivity of the Motion Detector Head.
The Motion Detector Head is most sensitive to movement across the detection zone, rather than movement toward or away from the Motion Detector Head.
Turn the dial anywhere between the minimum and maximum settings to adjust the level of sensitivity needed.
Note: Sensitivity is affected by the ambient air temperature. If it is hot outside, the sensor may have difficulty detecting changes in heat. In cold temperatures, the sensitivity is increased and may need to be adjusted.
Minimum Position
Turn the dial counterclockwise to the minimum setting (-). Ideal for cold winter conditions or when nuisance tripping is a problem. If the light is activated by small animals or rapid changes in heat, the sensitivity can be reduced by turning the knob counterclockwise towards the minimum setting.
Maximum Position
Turn the dial clockwise to the maximum setting (+). Ideal for hot summer conditions or to maximize range.
The TIME Adjusting Knob sets how long the Light stays lit after motion is no longer detected by the sensor.
Minimum Position
Turn the dial counterclockwise to the minimum for the light to stay on for 10 seconds after motion is no longer detected.
Mid Range
Adjusting the dial between the Minimum and Maximum to choose any time between 10 seconds and 100 seconds for the light to stay on after motion is no longer detected.
Maximum Position
Turn the dial clockwise to the maximum for the light to stay on for 100 seconds after motion is no longer detected.
The LUX Adjusting Knob tells the sensor the level of darkness that must be reached before the Light turns on.
Minimum Position
Turning the dial counterclockwise to the minimum setting lowers the sensor level. The sensor will only trigger the light to turn on at dusk or when it is dark out. This is the ideal position for general evening and night operation.
Maximum Position
Turning the dial clockwise to the maximum setting increases the sensor level. The light will go on in most situations ranging from dark to daylight.
Note: If the Security Light is not operating at night due to interference from a street light or other interference, turn the LUX knob towards the maximum setting . Adjust the dial as needed between the minimum and maximum settings to achieve the desired level of sensitivity.
After the battery is charged and the control Knobs are set, walk slowly around the detection area. The sensor detects infrared radiation given off by a person or animal. This triggers the Light to turn on. The Light should go on in the area that you set up the Security Light to monitor.
Adjust the Knobs and sensor and re-test until the unit functions as desired.
Repeat the test procedure as needed when there are weather and/or temperature changes.
Procedures not specifically explained in this manual must be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.
Problem | Possible Causes | Likely Solutions | |||
Light won't turn on. |
|
| |||
Light turns on during day. | LUX control is set too close to | Turn knob towards | |||
Light flashes on and off with clicking sounds. | Low battery. | With Switch set to "OFF", allow to charge in full sunlight for 3 days before further use. | |||
Light stays "ON". |
|
| |||
Light turns ON and OFF. |
|
| |||
Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect Battery and Charger power supply before service. |
Record Your Product's Serial Number.
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Parts may not be interchangeable. Specify item number when ordering.
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Part | Description | Qty |
1 | Lamp | 1 |
2 | Solar Panel | 1 |
3 | Mounting Screw | 6 |
4 | SMD LED Panel | 60 |
5 | Battery Housing | 1 |
6 | Motion Detector Head | 1 |
7 | Mounting Bracket | 1 |
8 | Power Switch | 1 |
9 | Solar Power Input | 1 |
10 | Solar Panel Mounting Base | 1 |
11 | LUX Adjusting Knob | 1 |
12 | SENS Adjusting Knob | 1 |
13 | TIME Adjusting Knob | 1 |
14 | Battery (not shown) | 1 |
15 | Solar Power Cable (not shown) | 1 |
Visit our website at: http://www.harborfreight.com
Email our technical support at: productsupport@harborfreight.com
For technical questions, please call 1-888-866-5797.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Bunker Hill Security 56213, 56408 - Led-Solar Security Light Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the 56213 that isn't answered in the manual? Leave your question here.