Table of Contents
Advertisement
Quick Links
®
1. PACKING LIST
Quantity
Name
1
Keypad
1
User manual
Screw driver
1
2
Rubber plug
2
Self tapping screws
1
Star screws
Please ensure that all the above contents are correct. If any are missing please notify the supplier of
the unit.
ACKP50EM-I
Remarks
Φ20mm×60mm,Special for keypad
Φ6mm×30 mm, used for fixing
Φ4mm×28 mm, used for fixing
Φ3mm×6mm, used for fixing
MANUAL ACKP50EM-I
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for GESS ACKP50EM-I
- Page 1 ® MANUAL ACKP50EM-I ACKP50EM-I 1. PACKING LIST Quantity Remarks Name Keypad User manual Φ20mm×60mm,Special for keypad Screw driver Φ6mm×30 mm, used for fixing Rubber plug Φ4mm×28 mm, used for fixing Self tapping screws Φ3mm×6mm, used for fixing Star screws Please ensure that all the above contents are correct. If any are missing please notify the supplier of...
-
Page 2: Quick Reference Programming Guide
® MANUAL ACKP50EM-I 2. QUICK REFERENCE PROGRAMMING GUIDE Master Code To enter the programming mode 999999 is the default factory master code To exit from the programming mode Note that to undertake the following programming the master user must be logged in... -
Page 3: Specifications
® MANUAL ACKP50EM-I 4. FEATURES Strong Zinc Alloy Electroplated anti-vandal case Full programming from the keypad 2000 uses, supports Card, PIN, Card + PIN Can be used as a stand alone keypad Backlight keys Wiegand 26 input for connection to external reader... -
Page 4: Installation
® MANUAL ACKP50EM-I 6. INSTALLATION Remove the back cover from the keypad using the supplied special screw driver Drill 2 holes on the wall for the Self tapping screws and I hole for the cable Put the supplied rubber bungs to into the two holes Fix the back cover firmly on the wall with 2 Self tapping screws... -
Page 5: To Reset To Factory Default
® MANUAL ACKP50EM-I Common power supply diagram: Special power supply diagram: 8. TO RESET TO FACTORY DEFAULT Disconnect power from the unit Press and hold # key whilst powering the unit back up On hearing two “Di” release # key, system is now back factory settings... -
Page 6: Anti Tamper Alarm
® MANUAL ACKP50EM-I 9. ANTI TAMPER ALARM The unit uses a LDR (light dependent resistor) as an anti tamper alarm. If the keypad is removed from the cover then the tamper alarm will operate. 10.SOUND AND LIGHT INDICATION Operation Status... - Page 7 ® MANUAL ACKP50EM-I To add a user in either card or PIN mode, i.e. in the mode. (Default setting) To add a Pin user User ID number The ID number is any number between 1 & 2000. The PIN is any four digits between 0000 &...
- Page 8 ® MANUAL ACKP50EM-I To delete a card user by card number. Card number Note users can be deleted continuously without exiting This option can be used when the programming user want to make the change but the card has lost...
-
Page 9: Door Settings
® MANUAL ACKP50EM-I 11.2 Door Settings To set door relay strike time Master Code 0〜99 0-99 is to set the door relay time 0-99 seconds Door Open Detection Door Open Too Long (DOTL) warning. When used with an optional magnetic contact or built-in... - Page 10 ® MANUAL ACKP50EM-I 12.THE UNIT OPERATING AS A WIEGAND OUTPUT READER In this mode the unit supports a Wiegand 26 bit output so the Wiegand data lines can be connected to any controller which supports a Wiegand 26 bit input.
Need help?
Do you have a question about the ACKP50EM-I and is the answer not in the manual?
Questions and answers