Summary of Contents for LAUNDRY SOLUTION SX071000A
Page 1
LAUNDRY SOLUTION CO., LTD. Tel : 076-617171 / 089-7246756 / 086-2762580 Website : www.laundryparts.in.th Email : Laundrypart@gmail.com SX071000A Washer-extractor Controller User Manual Please read the manual carefully before installation and operation Software version X1.LD028A.X07.001-1 V100A1 X1.LL013A.X07.001-1 Rights Reversed, Pirate Punished...
Page 2
Safety Precautions Please fi the controollero to avoid vibroate droors Please install the controollero in the metal oro not inflammable boarod Installatio Please guaroantee electroic cabinet temreroaturoe among -10℃~+50℃, adding ventilating when necessaroy Do not eirose in the sunlight, stroong airoflow and mist ...
Page 3
Symbol explanation Please familiaroize youroself with the following standarod waroning symbols They aroe used throoughout this manual to alerot you the rossible hazarods Anyone installing, oreroating and serovicing this controollero must underostand these symbols and follow all the safety roules in this manual It will cause the dangerous situation, possibly will cause the personal injury or death when error using.
1 GENERAL This schematic rhoto is just foro roeferoence SX071000A controller is specially designed for the control of the automatic washer extractor. It features stability and reliability in operation. SX071000A controller has very convenient human-machine interaction interface with liquid crystal display to show state of operation of the machine including temperatures at Led display and thus helps monitoring effect.
SX071000A Washer-extractor Controller 2.1.2 I/O control Board M CU 2.2 Electric Connection Level sensor 5-3.96 J1 4-3.96 3-3.96 6-3.96 GW 107 M CU M otor overload Em ergency Stop LL013A Extr shock Door sw itch Inverter error J5 10-3.96 AC220/24VDC...
SX071000A Washer-extractor Controller 2.3 Inverter Parameter Setup2.3.1 Digital Input Digital input List The controller parameter “Base number of inverter” is 0: Wash Wash Eitroac Eitroac Eitroac Eitroac Eitroac Eitroac Eitroact Forowaro Reveros High 4 Forowaro Balanc Middle High 1...
SX071000A Washer-extractor Controller 04-04~04-07 MI1~MI4 01~04 Speed 05-00~05-14 Step freq Need 2.32 RS485Rs485 mode can’t be used When inverter type is punp inverter.
SX071000A Washer-extractor Controller 3 Buttons introduction Icon Function [Wash] button Press this button to select Standard\Delicate\Heavy washing ways and stopping washing. [Cold Water] button Switch between starting adding cold water1 and stopping adding cold water1 by pressing this button when the actual level is lower than the set level.
Page 12
SX071000A Washer-extractor Controller [Supply1] button Under “manual” mode, the supply1 will work for 30 seconds by pressing this button and you also can stop the supply1 during supply1 working by pressing this button. [Supply2] button Under “manual” mode, the supply2 will work for 30 seconds by pressing this button and you also can stop the supply2 during supply2 working by pressing this button.
SX071000A Washer-extractor Controller 4 Running 4.1 Startup After power is on, the LCD shows the startup interface for 10 seconds.. 4.2 Manual Running Mode 4.2.1 Start Manual Running Power on and close the door, it will enter into “Closed status”. Lock the door by pressing [stop] button.Enter into “Manual mode”...
SX071000A Washer-extractor Controller 4.3.7 Lock or UnlockPress [stop] button to lock the door under closed status. Press [stop] button to unlock the door under locked status. Note: If the temperature, water level is higher than the safety value, user can not unlock and...
SX071000A Washer-extractor Controller 5 Programming There are 5 programs on the controller. They are pre-set to prog1(standard), prog2(sheets), prog3(rags), prog4(uniform), prog5(towels). 5.1 Create New Program 5.1.1 Select and enter Select your desired program under “Idle” status, press [↑] [↓]button, it will enter into “program”...
SX071000A Washer-extractor Controller 6 ParameterNote: All parameters have already been configured for the machines in factory. Don’t intend to modify any parameter without any special requirement. Some modification will lead to abnormal work. After power is on, the LCD shows the startup interface. Press [Up] and [Down] button at the same time during the 10 seconds counting down.
Page 17
SX071000A Washer-extractor Controller Group Items Default Range Introduction Level 1:Machine capacity 20KG 1~200KG Factory 2:Language Chinese Chinese, English End User Celsius, 3:Temperature units Celsius End User Fahrenheit Open drain valve automatic after open the door for the safety of the...
Page 18
SX071000A Washer-extractor Controller High Set the overbrim level. Drain valve will open when water higher than 5:Overbrim level 99cm End User Level~99cm the overbrim level. 6:Auto re-fill when low No,Yes Auto re-fill when level is lower than set value. End User Auto re-fill when difference between current and set is larger than 7:Level diff.
Page 19
SX071000A Washer-extractor Controller Heavy wash stop time, includes forward and reverse. 7:Heavy wash stop time 5 Sec 0~255 Sec End User When “Heavy wash stop time” is set to “0”, it becomes single wash. 1~ Max speed of 8:Wash speed 40 rpm Default speed of norm wash.
Page 20
SX071000A Washer-extractor Controller Mid Extract End User 20:High extract 1 speed 500rpm Speed~Hi 2 Speed of high extract 1. Speed Hi 1 Speed~Hi 3 End User 21:High extract 2 speed 700rpm Speed of high extract 2. Speed Hi 2 Speed~Hi 4...
SX071000A Washer-extractor Controller 6.3 PUNP inverter setup On the top menu Of parameter setup interface, press [↑] or [↓] button to select “3: PUNP inverter setup” and press [ENTER] button to enter into this item. Note: Parameter 6.1 “Inverter type” should set as “PUNP Inverter” and 6.2 “Invertercontrol mode” should set as “Rs485”.
Page 22
SX071000A Washer-extractor Controller 6:Slip compensation gain 300.0 7:Slip comp. filter time 1.0s 0.1 25.0s 8:Vibration damping 0~200 9:Base frequency 50.00Hz 1.00 650.00Hz 10:Max. output voltage 220V 150 500V “V/F frequency 11:V/F frequency F4 50.00Hz F3” Base frequency” “V/F voltage V3”...
SX071000A Washer-extractor Controller Please check whether strong or weak electricity insulate or not or Bkbd comm intfer machine whether to connect the earth or not. Parameter error Please contact with factory. Program error Please contact with factory. Controller failure Please contact with factory.
Page 25
SX071000A Washer-extractor Controller R, S or T phase loss Check the wiring Three input phases imbalanced Check input voltage 10)Input phase loss Adjust parameters to eliminate Serious oscillation of output oscillation Check the output wiring 11)Output phase loss Loss of output ( U, V or W)
SX071000A Washer-extractor Controller Check the connection of thermal 27)Thermal resistor open Thermal resistor disconnected resistor or call us 28) standby 7.2.2 Alarms of PUNP inverter Alarm name Description Remedies Motor thermal model detects the motor temperature rise is 1)Motor overload...