Advertisement
Quick Links
OPTIONAL WIRELESS WALL MOUNTED TOUCH
OPTIONAL WIRELESS WALL MOUNTED TOUCH
CONTROL FOR LANDSCAPE PRO V2 SERIES
CONTROL FOR LANDSCAPE PRO V2 SERIES
customerservice@modernflames.com
Part# MF-PRO-V2-WTC
Part# MF-PRO-V2-WTC
Owner/Installation Guide
07-00042
modernflames.com
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Modern Flames MF-PRO-V2-WTC
- Page 1 OPTIONAL WIRELESS WALL MOUNTED TOUCH OPTIONAL WIRELESS WALL MOUNTED TOUCH CONTROL FOR LANDSCAPE PRO V2 SERIES CONTROL FOR LANDSCAPE PRO V2 SERIES Part# MF-PRO-V2-WTC Part# MF-PRO-V2-WTC Owner/Installation Guide 07-00042 customerservice@modernflames.com modernflames.com...
- Page 2 Assembly, Parts & Hardware List What's in the Box WTC instruction guide o WTC assembly (PCBA with glass magnets adhered) P/N: 01-00141-1 o WTC Metal wall mounting bracket P/N: 02-00743 o AAA batteries (not sold separately) o Optional WTC 12 VDC Harness 13ft length P/N: 01-00141-2 o Hardware kit: Image is example only (not sold separately) #6x1/2"...
-
Page 3: Installation And Assembly
Installation and Assembly Install Option #1 Battery Powered Select a suitable location where you would like to install the wall touch control (WTC). NOTE: It must be within 20 feet of the fireplace and recommended in the same room for best performance. - Page 4 Installation and Assembly Level and cut clearance hole for wall control. If WTC is to be installed into furniture, the inside of included mounting bracket will be used to mark and cut a clearance hole for the wall controls components. Ensure the bracket is level prior to marking and cutting the hole.
- Page 5 Installation and Assembly Attach the metal bracket to the furniture or the low-voltage box with the included screws. NOTE: If other screws are to be used, they must be low profile screws or glass will not secure to the bracket. Insert two (AAA) batteries paying attention to the polarity on the board.
- Page 6 Installation and Assembly Install the WTC assembly on the bracket. The assembly will be secured by magnets. Pair the wall control with the fireplace following the pairing instructions on page 13. customerservice@modernflames.com modernflames.com...
- Page 7 Installation and Assembly Install Option #2 Wired Select a suitable location where you would like to install the wall touch control (WTC). It is required that this be done prior to finishing the wall, in order to run the cable to the fireplace from the desire location.
- Page 8 Installation and Assembly Locate the access point on the right side of the firebox and insert the low-voltage cable. Access point Gain access to the inside of the fireplace and locate the main PCBA. There is an access panel at the top of viewing area. Front glass must be removed to gain access to main PCBA. - Access panel screws along edge.
- Page 9 Installation and Assembly Locate the previously inserted low-voltage cable and plug it into PCBA. The connection on the board is labeled "12V+". Do not force connection, if it is not going in rotate 180° and reinsert. Ensure to leave a few inches of slack for serviceability. Connection on board Route the remaining cable to where the WTC will be installed.
- Page 10 Installation and Assembly Level and cut clearance hole for wall control. If WTC is to be installed into furniture, the inside of included mounting bracket will be used to mark and cut a clearance hole for the wall controls components. Ensure the bracket is level prior to marking and cutting the hole.
- Page 11 Installation and Assembly (Example of new construction box) Attach the metal bracket to the furniture or the low-voltage box with the included screws. NOTE: If other screws are to be used, they must be low profile screws or glass will not secure to the bracket.
- Page 12 Installation and Assembly Connect the low-voltage cable into the wall touch control connection in the rear. The connection on the back is labeled "DC12V". Do not force connection, if it is not going in rotate 180° and reinsert. Ensure to leave a few inches of slack for serviceability. Note: Do not use batteries when using in wired configuration connection.
- Page 13 Installation and Assembly Pair the wall control with the fireplace following the pairing instructions. Before beginning, read pairing instructions in their entirety. Locate and familiarize yourself with the manual touch controls on the fireplace and your wall touch control (WTC). Ensure the WTC has a battery installed or is connected to the 12V DC supply from the fireplace.
- Page 14 Digital Read out - Displays heat setting, thermostat setting, and timer setting Modern Flames - Reset Flame, Ember Bed, during use. Fades out when not in use. Down lighting, & Flame Speed to Modern Note: The thermostat sensor is located on Flames Orange &...
- Page 15 DO NOT RETURN TO STORE! CALL US FIRST For immediate help with installation, product information or if your product arrives damaged, please call our toll free number at: 1-877-246-9353 (Monday - Friday, 8:00AM - 5:00PM, AZ Mountain Time) Or email us at: customerservice@modernflames.com OUR STAFF IS READY TO PROVIDE ASSISTANCE customerservice@modernflames.com...
- Page 16 Thank you for choosing Modern Flames, we appreciate all our customers and hope you have many years of enjoyment of our products. Take a look at our other products from our RPG Brands family of companies GrandCanyonGasLogs.com For all your indoor, outdoor gas fireplaces & fire feature products.
Need help?
Do you have a question about the MF-PRO-V2-WTC and is the answer not in the manual?
Questions and answers