Summary of Contents for eXact PipeCut V800 System
- Page 1 PipeCut V 00 Ventilation System Operating manual 5-16 patents: US 7,257,895, JP 4010941, EP 1301311, FI 108927, KR 10-0634113...
- Page 3 Cermet blades can be sharpened a few times. Pipe Support V 00 We recommend to use Exact Pipe Support V 00 for to support the pipes when using Exact Pipecut V 00 pipe saw. These pipe holders are specially designed to be used with Exact Pipecut V 00 pipe saw.
- Page 6 EN60745 according to the provisions of the directives 2004/108/EC, 2006/42/EC. For more information, please contact Exact Tools at the following address. The technical le is available at the address underneath. The person authorized to compile the technical le: Helsinki, 1.9.2011...
-
Page 8: Table Of Contents
Contents english Translation of the original instructions Contents Technical data Package contents Safety Safety instructions Operation 10. Functional description 10. Product features 11. Before operating the tool 11. Connection to the mains power supply 11. Precise setting of the cutting point 11. -
Page 9: Technical Data
Also store this instruction book somewhere accessible to everyone using the pipe saw. In addition to these instructions, always follow the of cial work, health and safety regulations. The Exact PipeCut is meant for professional use only. Technical data... -
Page 10: Package Contents
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns. Exact PipeCut V 00 pipe saw Package contents: Please check the package contains the following items (page 4):... -
Page 11: Safety
Safety english General power tool safety warnings b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid WARNING: Read all safety warnings safety shoes, hard hat, or hearing protection and all instructions. used for appropriate conditions will reduce Failure to follow the warnings and instructions may personal injuries. -
Page 12: Operation
Safety english d) Store idle power tools out of the reach f) Never use damaged or incorrect blade of children and do not allow persons washers or bolt. The blade washers and unfamiliar operate the power tool. Power bolt were specially designed for your saw, tools are dangerous in the hands of untrained for optimum performance and safety of users. -
Page 13: Functional Description
(1,5 mm). With a spiral ventilation duct the maximum poisonous chemicals inside the pipe to be cut. thickness of the seam that the Exact Pipe Cut V 00 can cut through is 6 mm (0,24”). With the Exact PipeCut •... - Page 14 In case you are not using the supports you need to do the following. Make sure that there is enough space for the duct to rotate a full circle. Place the Exact Pipe Cut V 00 so that the electric cord is hanging in front of the duct from where you are standing (Figure C).
- Page 15 Operation english Fig E If you follow the scale of the Pipe Cut the cutting depth is normally 10 - 15 mm as the Pipe Cut locks into the correct sawing position. Finally lock the adjustment with the safety screw so that the adjusted position does not alter during sawing.
- Page 16 Overload protection and spin-speed regulator Exact V 00 is equipped with overload protection. When the blade is dull or the cutting speed is too high, the overload protection cuts power automatically.
-
Page 17: Installing And Changing The Saw Blade
Fig N There is a feature in the steering device of the Exact Pipe Cut V 00 (Fig.A/6) which, if needed, can improve the sawing result and facilitate to reach the starting point. Loosen the locking screw (Fig.O/1) with the M5 allen key that is attached to the handle of the pipe saw. - Page 18 Blade guard Make it a rule to clean the blade guard regularly, and pay special attention to keep the The Exact Tools Warranty Term is for 12 months moving blade guard movement from becoming from date of purchase. hampered. Lubricate the axis of the moving blade guard regularly.
- Page 19 Tips english Note: The Exact PipeCut Saw is to be shipped Keep the feeding speed constant. This will to the Authorized Warranty Repair Center freight extend the lifetime of the blade.For example prepaid. If the Exact PipeCut Saw is repaired cutting time for a steel pipe diameter of 6’’...
- Page 20 Exact Tools Oy Särkiniementie 5 B 64 00210 HELSINKI FINLAND Tel + 358 9 4366750 FAX + 358 9 43667550 exact@exacttools.com www.exacttools.com...
Need help?
Do you have a question about the PipeCut V800 System and is the answer not in the manual?
Questions and answers