Summary of Contents for Herutu ENS-HH01
- Page 1 Hard-hat-on Sensor ENS-HH01 Instruction Manual V1.10 Please use this Instruction manual correctly on reading well. Please keep it carefully to be able to read immediately, when required.
-
Page 3: Table Of Contents
6-2-1．For use with POKAYOKE plus .................... 12 6-3．Delete the pairing ........................12 7．Installation ............................13 7-1．Attach the ENS-HH01 to the hard hat ..................13 7-2．Replace the battery of ENS-HH01 ..................... 14 7-2-1．Battery Replacement ......................14 7-2-2．Procedure of battery replacement ..................14 7-3．Replace the touch sensor of ENS-HH01 ................... - Page 4 ENS-HH01 12．Troubleshooting ..........................24 13．After Service and Warranty ......................26...
-
Page 5: 1．Overview
ENS-HH01 1．Overview The hard-hat-on sensor “ENS-HH01”（referred to below as “the sensor”） is a wearable device that prevents accidents that occur when employees are not wearing hard hats. The sensor for detecting the wearing status of hard hats is integrated with the wireless unit. By attaching the sensor to a hard hat’s chin strap, it detects the wearing status of the hard hat in real time. -
Page 6: 2．Main Part And Accessories
Hard-hat-on sensor ENS-HH01 Coin battery CR2032 ×1 ENS-HH01 body ×1 *ENS-HH01 is delivered with a coin cell battery installed. Due to properties of the product, the touch sensor and other component directly touch a customer’s skin. *When you feel uncomfortable with your skin while wearing the sensor, stop using the sensor immediately. -
Page 7: Safety Precautions (Be Sure To Read This)
ENS-HH01 3. Safety Precautions (Be Sure to Read This) This section describes the matters to be observed in order to prevent harm to the users and other persons and damages to the property. ■The following marks and displays classify and describe the extent of harm and damage caused by failing to observe the display content and using this product wrongly. - Page 8 〇Also contact us in case of any trouble such as harmful radio interference to specified low-power radio stations for mobile objects identification or amateur radio stations. ENS-HH01 is equipped with the built-in wireless module HRF-2402. Available countries：Japan, Canada, USA, China, Thailand, Vietnam, Philippines and India.
- Page 9 ENS-HH01 ■FCC/ISED Warning Information about FCC Standard. FCC CAUTION Change or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
- Page 10 ENS-HH01 This radio transmitter (10608A-HRF2402) identify the device by certification number or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
-
Page 11: 4．Name And Function Of Each Part
ENS-HH01 4．Name and Function of Each Part Hard-hat-on sensor ENS-HH01 Front Back ⑥ ① ⑤ ② ④ ③ The LED for communication confirmation/battery check. It lights up/blinks ① LED (green) green according to the communication result. Test switch ② Used for testing wireless communication or for pairing. -
Page 12: 5．How To Use
Receiver Application Hard-hat-on Sensor TW-800R-EXL POKAYOKE plus ENS-HH01 *ENS-HH01 may detect the The wearing status can be identified by wearing status incorrectly due the color of the hard hat. to noise or other causes. Green・・・Hard hat is worn correctly. Red ・・・Chin strap is off. -
Page 13: How To Use
Press the test switch (pairing switch) of the sensor once to perform a test transmission. The LED indication patterns displayed immediately after the test switch was pressed indicate the following. Please refer to “5-6.LED indication patterns of ENS-HH01” for the LED indication patterns. Communication status with the receiver ... -
Page 14: Led Indication Patterns Of Ens-Hh01
ENS-HH01 5-6． LED indication patterns of ENS-HH01 Notification of the hard hat wearing status, regular transmission at the time interval of 5 minutes, communication status with the receiver when a test transmission is made, etc. are indicated by the LED indication patterns. -
Page 15: 6．Features And Settings
ENS-HH01 6．Features and settings 6-1．Initial settings To ensure sensing accuracy of the touch sensor, perform initial settings in the environment where hard hats are used. Once initial settings are completed, they are not needed to be performed every time. *The touch sensor does not work properly in factory default settings. Be sure to perform initial settings before using the sensor for the first time. -
Page 16: Pairing(Registration)
ENS-HH01 6-2．Pairing(registration) Before using the sensor, pair (register) the sensor with a communication target device. By pairing them, they recognize an identification signal from each other and communicate with each other. 6-2-1．For use with POKAYOKE plus The communication target is Pokayoke receiver. -
Page 17: 7．Installation
ENS-HH01 7．Installation 7-1．Attach the ENS-HH01 to the hard hat Insert a hard hat’s chin strap into the groove on the back of the sensor. Avoid the adjuster for adjusting the length of the chin strap. Adjust the length of the chin strap before mounting ENS-HH01 on the chin strap. -
Page 18: Replace The Battery Of Ens-Hh01
ENS-HH01 7-2．Replace the battery of ENS-HH01 7-2-1．Battery Replacement When low battery level is indicated, replace the battery. Observe the following when replacing the battery. Not doing so may lead to lack of waterproof or damage to the product. ・Wipe off dirt and moisture from the surface before replacing the battery. - Page 19 ENS-HH01 ③Install a new battery. Install coin cell battery (CR2032). Make sure that the positive（＋）side faces upward. When the battery is tilted or the claws of the battery holder come off, remove the battery and install it again. ・Battery is tilted.
- Page 20 ⑥Check if the touch sensor is working properly. Touch both touch sensors with your finger and make sure that the touch sensors can transmit data by the LED. *Please refer to “5-6.LED indication patterns of ENS-HH01” LED (Green) for the LED indication patterns.
-
Page 21: Replace The Touch Sensor Of Ens-Hh01
ENS-HH01 7-3．Replace the touch sensor of ENS-HH01 7-3-1．Touch sensor Replacement Do not use any of the following touch sensors, and replace it with a new one immediately. ・Deformed ・With significant scratches and chips ・Damaged or cracked ・Discoloration is identified *The touch sensor (S20006-25-00) is available for replacement separately. - Page 22 ENS-HH01 ③Attach a new touch sensor. Attach the touch sensors so that the leg directions (long and short legs) are aligned. ・The leg directions are aligned. ・The leg directions are misaligned. ④Put the cover back on. Make sure that there is no gap between the Cover waterproof rubber seal and the cover.
- Page 23 ⑥Check if the touch sensor is working properly. Touch both touch sensors with your finger and make sure that the touch sensors can transmit data by the LED. *Please refer to “5-6.LED indication patterns of ENS-HH01” LED (Green) for the LED indication patterns.
-
Page 24: 8．Communication Specification
ENS-HH01 8．Communication Specification For use of the sensor with a PC (POKAYOKE plus) or PLC, LAN communication of the POKAYOKE receiver is explained below. 8-1．Data type setting of receiver When the hard hat’s wearing status changes, when transmitting regularly or when performing test transmission, the receiver receives signals transmitted from the sensor and communicates with the external device (PC, PLC, etc.). -
Page 25: Receiver Data Format
Checksum it is converted to ASCII data for 2byte. (*5) The system area contains system specific data for “ENS-HH01”. When using the output data in your environment, read and discard the data in the system area. “ENS-HH01” transmits wireless signals when the hard hat wearing status changes, when transmitting regularly every 5 minutes or when transmitting a test signal. -
Page 26: 9．Cautions For Use
ENS-HH01 9．Cautions for use ・Waterproof and dustproof function The device is rated at IP65 waterproof and dustproof rating, but the waterproof and dustproof function cannot be achieved if the device is not assembled properly. When disassembling the device for battery replacement or other purposes, carefully read “7. -
Page 27: 10．Specifications
ENS-HH01 10．Specifications Item Specifications <Japan> Radio equipment specified in Article 2 paragraph 1 item(19) of the Radio Law *Specialized radio equipment: Low power data communication system in the 2.4 GHz band Compliance Standards Article 49-20 paragraph 1 of the Ordinance Regulating Radio Equipment <USA>... - Page 28 ENS-HH01 12．Troubleshooting Phenomenon Cause and remedy The sensor does not transmit. Battery capacity is low. LED does not light up. →Please replace the battery (CR2032）. Pairing is not done. (Not registered) →Perform pairing with the receiver to communicate with The LED blinks 3 times after transmitting.
- Page 29 →Adjust the length of the hard hat's chin strap so that the touch sensor to touch your skin directly. ENS-HH01 is attached in the opposite direction. →Attach the sensor to the chin strap to allow the touch sensor to touch your skin.
- Page 30 This regulation (hereinafter referred to as the "Regulation") is for post-shipment warranty provided by HERUTU ELECTRONICS CORPORATION (hereinafter referred to as the "Company") so that you can use the Company's product you have purchased with confidence. The Regulation does not apply to special order products (custom products).
- Page 31 This regulation (hereinafter referred to as the "Regulation") shall be applied to paid repair service (hereinafter referred to as the "Service") provided by HERUTU ELECTRONICS CORPORATION (hereinafter referred to as the "Company"). The Regulation does not apply to special order products (custom products).
- Page 32 ENS-HH01 describes the Company's old repair regulation, the latest Regulation will still apply. Subject of the Regulation The Service is provided for the Company's products that are "beyond the scope of the warranty specified in the warranty regulation" and "from the sales start date to the end date of the repair period (seven years from the production end date)".
- Page 33 ENS-HH01 etc., the Company may use recycled parts or alternative parts at the time of repair at its discretion. B) The Company may, at its own discretion, collect the removed parts for the purpose of recycling or analysis at the time of parts replacement through the regulation of the Service. Please note that the collected parts are the property of the Company and will be recycled, used or discarded at its discretion.
- Page 34 ENS-HH01 time of damage. 11. Additional notes A) The Company cannot restore stickers, LCD protective sheets, and coloring applied to the outer casing parts that you have attached yourself. In addition, if advertisement stickers were affixed at the time of sale, they cannot be newly prepared as repair parts when replacing the outer casing parts.
- Page 36 HERUTU ELECTRONICS CORPORATION 422-1 Higashimikata-cho, Kita-ku, Hamamatsu, Shizuoka, 433-8104 Japan (Sales dept) TEL.+81-53-438-3555 FAX. +81-53-438-3411 Website URL https://www.herutu.co.jp/en/ E-mail info@herutu.co.jp...
Need help?
Do you have a question about the ENS-HH01 and is the answer not in the manual?
Questions and answers