Summary of Contents for OBaby OBA-BikeT1
- Page 1 Machine Translated by Google © OBA Srl VIA LEPANTO, 132 VAT and Fiscal Code: 07750391216. The products are subject to change without notice. WWW.OBA.SRL OBA-BikeT1 OBA-BikeT025 USER MANUAL...
- Page 2 Machine Translated by Google The new electric bicycle from the OBA company is available in three colours: black, red and grey, all painted with an electrostatic spray which guarantees a uniform and resistant finish. The 48V and 17.5AH and 15.5AH lithium battery is combined with a 48V 2A battery charger, which allows a charging time of only 5-6 hours.
-
Page 3: Left Handlebar
Machine Translated by Google LEFT HANDLEBAR Rear brake lever (behind handlebar grip in this photo). The rear brake is activated by pressing the left brake lever. THIS IS *THE OPPOSITE OF A TRADITIONAL BIKE. B Left Handlebar Grips C On/ Off Button: Press for 3 seconds to turn your E-Bike on or off D Speed Speed Increase Button/ Headlight: Press once to increase speed Press for 3 seconds to turn on/off the... - Page 4 Machine Translated by Google RIGHT HANDLEBAR Gears - by pressing the button while pedalling, it is possible to increase the gears from 1 to 21. The gearbox is labeled with the corresponding gear selection. B Rear derailleur: by pressing the lever while pedalling, it is possible to reduce the gears from 21 to 1. The derailleur is labeled with the corresponding gear selection C Front brake lever (behind the handlebar grip in this photo).
- Page 5 Machine Translated by Google Assembly...
- Page 6 Machine Translated by Google REMOVE PACKAGING 1 Unpack your electric OBA. 2 Tools needed 3 Remove the packing materials 4 Remove the front wheel...
-
Page 7: Handlebar Assembly
Machine Translated by Google HANDLEBAR ASSEMBLY Secure the front shock absorber Tighten the side screws A, B Loosen the screws A, B of the sides of the upright "Before installation, pay attention Fit the handlebar to the stem then replace 4 Remove the front 4 bolts from the stem 6 Adjust the handlebar to your needs then cover, then remove the cover. - Page 8 Machine Translated by Google HEADLIGHT AND FRONT WHEEL ASSEMBLY 1 Remove the bolt from the headlights, then Remove the fork protector Turn the bike upside down. adjust the headlights and front grille to the correct Adjust the seat height and rotate the handlebar The protective rod can be removed and thrown away position and tighten the bolts.
- Page 9 Machine Translated by Google ASSEMBLING AND ADJUSTING THE PEDALS AND THE SADDLE “L” mount counterclockwise to the Check the left and right pedals The "R" pedal is fixed clockwise on the chain The 'R' right side is mounted on the crown side crank "The right side is mounted on the opposite side...
- Page 10 Machine Translated by Google CLOSING THE CHASSIS AND REMOVING THE BATTERY 1 Push the lever forward. Release the lever and fold the bike in half Open the lock, the lock cylinder must be fully A Self-locking safety lever retracted, pull the key You can remove the battery...
- Page 11 Machine Translated by Google Battery recharge Direct recharge The battery can be charged without removing it from the bike or alternatively it can be removed and charged in another location...
- Page 12 Machine Translated by Google BATTERY RECHARGE ATTENTION Connect the battery first, then connect the power and make sure the red LED of the charger is on. The charger will charge the full battery within 3-6 hours. The red LED indicates that the battery is being charged. The green LED indicates that the battery is fully charged.
- Page 13 Machine Translated by Google...
- Page 14 Machine Translated by Google FIGURE 1 FIGURE 2 BRAKES It is important for your safety to instinctively know which brake lever controls which brake. On your OBA E-Bike, the right brake lever controls the front brake. The left brake lever controls the rear brake. Your OBA E-Bike is equipped with hydraulic disc brakes for maximum reliability.
-
Page 15: Troubleshooting
Machine Translated by Google TROUBLESHOOTING If your OBA E-Bike doesn't work, check all Quick Fittings to make sure they haven't become loose or disconnected. Simply unroll the black coiled wire cover until the quick release fitting is visible, disconnect and reconnect the fittings. -
Page 16: Inspection And Maintenance
Machine Translated by Google INSPECTION AND MAINTENANCE Handbrake cut-off power When your bicycle is equipped with a brake cut-off system, it will automatically cut off the power when the brake is applied. Low Voltage Protection When the battery output voltage reaches the limit, the electronic control system will automatically cut off the power to protect the battery. When the battery reaches its minimum voltage, it is necessary to switch to pedalling.
Need help?
Do you have a question about the OBA-BikeT1 and is the answer not in the manual?
Questions and answers