Advertisement
Table of Contents
The Automatic Janitor is a fully programmable automatic flush control device for urinals. The Automatic Janitor converts most
urinals into water efficient fixtures by controlling the amount of daily flushes. The flush intervals can be programmed to flush
once every 1, 2, 3, 4, 6, 12, or 24 hours. The Automatic Janitor was designed to be used in conjunction with a urinal
deodorizer/screen to provide for ultimate water efficiency while eliminating odors.
<
Automatic Janitor Components
Collar
Gasket
=
Installation
PRE-INSTALLATION NOTE:
Although not necessary, it is recommended to shut off
water supply at stop.
c
Using the supplied collar wrench, loosen handle
from flush valve.
d
Remove handle from flush valve.
Note: A small amount of water may drip out while
removing handle so be prepared to collect
it with a rag or towel.
e
Place collar gasket into collar nut and attach the
Automatic Janitor unit where the handle was removed.
f
Tighten collar nut using the supplied collar wrench.
NOTE: Save removed handle in case you need to reuse
for service of Automatic Janitor unit.
HSM-801AJ
Series
Manual
Flush Key
Automatic Janitor Unit
AUTOMATIC JANITOR
SIDEMOUNT for Urinals
Installation and Operation Manual
User Approaches
Compartment
Four (4) "C" Cell
Alkaline Batteries
(Factory Installed)
c
Collar
Wrench
e
Collar
Collar Nut
Gasket
Page 1
User Uses Urinal
Battery
Wrench
Collar
Wrench
d
f
User Leaves
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for AMTC HSM-801AJ Series
Summary of Contents for AMTC HSM-801AJ Series
- Page 1 AUTOMATIC JANITOR HSM-801AJ SIDEMOUNT for Urinals Series Installation and Operation Manual User Uses Urinal User Approaches User Leaves The Automatic Janitor is a fully programmable automatic flush control device for urinals. The Automatic Janitor converts most urinals into water efficient fixtures by controlling the amount of daily flushes. The flush intervals can be programmed to flush once every 1, 2, 3, 4, 6, 12, or 24 hours.
- Page 2 > Set Flush Program Once installed and before activation, the Automatic Janitor unit must be programmed to flush at a specific interval of time. The unit can be set to flush once every 1 Hour, 2 Hours, 3 Hours, 4 Hours, 6 Hours, 12 Hours, or 24 Hours. A Flush Test Setting is included to test for proper installation of the unit.
-
Page 3: Battery Replacement
Manual Flush The Automatic Janitor includes a manual flush option. To activate a manual flush simply insert the Manual Flush Key (included) into the slot located on the side of the unit and press until flush is activated. SUGGESTION: The Manual Flush Key can be used to initiate a manual flush at any time. The key should be kept in a safe place or be attached to key chain of custodial staff for easy access. -
Page 4: Parts List
Parts List Ref. # Part # Description HSM-AAAJ AUTOMATIC JANITOR Sidemount Actuator Assembly HSM-BTAJ AUTOMATIC JANITOR Sidemount Battery Tray HSM-SCAAJ AUTOMATIC JANITOR Sidemount Side Cover Assembly HSM-SCSAJ AUTOMATIC JANITOR Sidemount Side Cover Screw Page 4... -
Page 5: Warranty
FOR A PERIOD OF FIVE (5) YEARS FROM DATE OF PURCHASE, WHEN PROPERLY INSTALLED AND UNDER NORMAL USE AND SERVICE. THESE PROVISIONS DO NOT INCLUDE THE BATTERIES SHIPPED WITH THE PRODUCTS. A DEFECTIVE PRODUCT MAY BE RETURNED TO AMTC OR ITS AUTHORIZED REPRESENTATIVES WITHIN FIVE (5) YEARS FROM DATE OF PURCHASE WITH THE PROPER INVOICE OF PURCHASE.
Need help?
Do you have a question about the HSM-801AJ Series and is the answer not in the manual?
Questions and answers