Bauer 2209C-B, 59299 - 190 Watt Power Source Battery Inverter Manual

IMPORTANT SAFETY INSTRUCTIONS

WARNING SYMBOLS AND DEFINITIONS
	This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
	Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
	Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
	Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
	Addresses practices not related to personal injury.

SAVE THESE INSTRUCTIONS

Read all safety warnings, instructions, illustrations and specifications provided with this tool.

Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

1. Output non-sinusoidal.
2. Do not obstruct ventilation openings or mount in zero clearance compartment. Overheating may increase the risk of fire and electric shock.
3. Do not expose to rain or use in damp locations.
4. Remove the battery before servicing.
5. Neutral floating.
6. For use with Bauer 20V Li-Ion battery packs (sold separately).
7. Do not use inverter if it has been dropped or impacted sharply. Use of a damaged device increases the risk of fire.
8. Remove the battery pack from the inverter when not in use.
9. Do not disassemble the battery inverter.
10. Keep out of the reach of children.
11. Store power inverter indoors and out of the reach of children.
12. AC Output must be used for powering devices of 150W or less. Connecting large loads to the inverter can lead to damage.
13. Plugs must properly fit the outlet without being forced. Do not insert any plug into the inverter if it does not fit easily into place.
14. Power inverter must be kept in cool environment. Keep away from heat.
15. Do not use power inverter near flammable gases or fumes. Do not power medical equipment with this power inverter.
16. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
17. Use inverter only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
18. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
19. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
20. Do not use a battery pack or inverter that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
21. Do not expose a battery pack or power inverter to fire or excessive temperature. Exposure to fire or temperature above 140°F may cause explosion.
22. Follow all charging instructions and do not charge the battery pack outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.
23. Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
24. Do not modify or attempt to repair the inverter or the battery pack except as indicated in the instructions for use and care.
25. 
    The battery Charger gets hot during use.
    The Charger's heat can build up to unsafe levels and create a fire hazard if it does not receive adequate ventilation, due to an electrical fault, or if it is used in a hot environment. Do not place the Charger on a flammable surface. Do not obstruct any vents on the Charger. Especially avoid placing the Charger on carpets and rugs; they are not only flammable, but they also obstruct vents under the Charger. Place the Charger on a stable, solid, nonflammable surface (such as a stable metal workbench or concrete floor) at least 1 foot away from all flammable objects, such as drapes or walls. Keep a fire extinguisher and a smoke detector in the area. Frequently monitor the Charger and Battery Pack while charging.

Lithium Battery Safety Warnings

LITHIUM BATTERIES STORE A LARGE AMOUNT OF ENERGY AND WILL VENT FIRE OR EXPLODE IF MISTREATED:

1. Keep Battery Pack dry.

Symbology

V	Volts
	Direct Current
~	Alternating Current
A	Amperes
	WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved safety goggles with side shields.
	Read the manual before set-up and/or use.
	WARNING marking concerning Risk of Fire. Do not cover Charger ventilation ducts. Charge on fireproof surface only.
	WARNING marking concerning Risk of Electric Shock. Properly connect Charger's power cord to appropriate outlet.
	WARNING marking concerning Risk of Explosion. Do not puncture, short, or open battery packs and do not charge damaged battery packs.

Specifications

Functions

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

General Operation

Only use with:

• Laptops, Tablets, and Cell Phones.
• Fans.
• Lights.
• Other devices of 150W or less.

1. Slide the Battery Pack onto the Inverter.
2. Connect a device to a USB Charging Port, or the AC Outlet.

Note: If the AC output is overloaded, the power button backlight will be red, remove the connected load and press the power Button to restore AC output

3. Turn the Inverter ON/OFF by pressing the Power Button.

Note: Inverter will shutdown when no activity is detected for 3 minutes.

Note: Cooling fan will automatically turn ON and OFF during operation. AC output will shut off if overheated.

Maintenance and Servicing Instructions

Procedures not specifically explained in this manual must be performed only by a qualified technician.

Cleaning, Maintenance, and Lubrication

1. Li-Ion BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY. Do not short, incinerate or open battery.

Troubleshooting

Problem	Possible Causes	Likely Solutions
Inverter will not turn on	Battery Pack not properly connected. Battery Pack not properly charged. Battery Pack burnt-out.	Remove Battery Pack, make sure there are no obstructions, reinsert the Battery Pack according to its shape (it should only fit one way), and press firmly until the Battery Pack locks in place. Make sure Charger is connected and operating properly. Give enough time for Battery Pack to recharge properly. Dispose of old Battery Pack properly or recycle. Replace Battery Pack.
No AC Output	Inverter is overloaded. Defective device connected	Check if inverter output rating has been exceeded. Try a different device.
WorkLight not working	Power Switch is OFF.	Power Switch must be ON for Worklight to work.
USB-C will not charge device	Device may require 20V to charge, this inverter provides up to 15V through USB-C.	Check device operator's manual and verify that 20V is not required for charging.
Overheating	Blocked vents.	Keep all vents clear for proper ventilation. Wear ANSI-approved safety goggles and NIOSH-approved dust mask/respirator while blowing dust out of unit while using compressed air.
Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect Battery Pack power supply before service.

Record Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Replacement parts not available. Refer to UPC 193175465474.