Advertisement
Quick Links
Advertisement
Summary of Contents for GARDENMAN GMC4110
- Page 1 GMC4110...
-
Page 4: Before The First Use
BEFORE THE FIRST USE Be sure to read the full instructions! Read the user manual before use before first use. Instructions contain important information for the safe use of this product. Add fuel There is no fuel in the engine! Fuel must be added to the tank before use. - Page 5 Instruction manual · This instruction manual applies for this device. It contains important information for starting the use and handling with the product. · Before you start using the device, read the instruction manual carefully and in its entirety, specially the safety instructions. Failure to follow this instruction manual can result in serious bodily injuries or damage to the device.
-
Page 6: General Safety Measures
replace or modify its parts. Only service authorised by the manufacturer is allowed to perform works on the device. · Do not overload the tool. Overloading and repeated engine blocking can damage the tool, and consequently reduce the lifetime of the product. ·... - Page 7 · Some tasks require special training and special skills. If you are in doubt, contact an expert. · Beginner users need training with an expert to work with the tool or they must attend a course in an educational institution to use the tool.
- Page 8 risk of injury. · Wear suitable clothing Do not wear wide clothes, jokes, ties or jewellery. Do not bring hair, clothes and gloves close to movable parts. Loose clothing, jewellery or long hair can get stuck in moving parts. · Always use hearing protection. The noise generated by the tool can cause hearing damage.
- Page 9 slippery. · Children, other persons and animals must not be in the vicinity when using a chainsaw. In the event of a distraction, you can lose control of the chainsaw. · Before sawing, make sure that there are no persons, animals or objects in the danger zone.
- Page 10 filling site. This will prevent the exhaust fumes of the engine to ignite the spilled gasoline. · Never work alone! In an emergency, someone must be near. · Check the correct operation of the safety devices before starting work. Do not use a chainsaw if it is damaged or does not work reliably. ·...
- Page 11 · In case of significant changes in behaviour, immediately turn off the chainsaw and find the cause. · Only saw wood. Do not use chainsaws for work for which it is not intended. Do not use chainsaws for sawing plastic, masonry or non- wood construction materials.
- Page 12 KICKBACK Kickback may occur when the tip of the bar touches the object or when it bends and the chainsaw gets stuck in the cut. A touch with a tip of the bar may in some cases lead to an unexpected, rearward reaction, in which the bar is thrown up in the direction of the operator.
- Page 13 · Start the cut at full power and keep the chainsaw at the highest speed during sawing. · Be extremely careful when inserting a chainsaw chain into a previously created cut. · Do not saw branches or parts of wood where change of position may occur during sawing or where the cut may close during sawing.
- Page 14 C. Mandatory use of protective equipment for protection of the head, hearing and eyes. D. Mandatory use of protective gloves. E. Mandatory use of protective safety shoes. F. Noise level G. Refuelling cap H. Chain oil cap I. Fuel pump membrane J.
- Page 15 Installing the guide bar and chain WARNING! Wear protective gloves when installing. 1. Push the guard towards the chain to release the chain brake. (1) 2. Unscrew the screws and remove the unit cover. (14) 3. Install the toothed support on the motor unit. (15) 4.
- Page 16 1. Place the chainsaw with the right side on the appropriate base. 2. Unscrew the fuel tank cap (9) and remove it. 3. Add mixture for two-stroke engines in the fuel tank. Be careful not to overfill the tank. NOTE: If you overfill the tank, immediately wipe up the spilled fuel. Wait for any residual fuel to evaporate before restarting the engine.
- Page 17 3. Push the choke out to position 1. (B2) 4. Firmly grasp the front handgrip with your left hand, and the ignition handgrip with your right hand. (B3) 5. Pull the ignition lever towards you until you feel resistance. 6. Pull the lever firmly against you. NOTE: Do not pull the handle fully, as it may damage the starter.
- Page 18 1. Push the hand guard forward to activate the chain brake. 2. Pull the hand guard back to release the chain brake. Checking the brake Regularly check if the chain brake is working properly. 1. The chainsaw should be turned on. 2.
- Page 19 the lower side of the triangular shape. (C1) NOTE: The horizontal cut should be precise and levelled. When felling, about 1/10 of the diameter of the trunk must remain as a break-off edge. Do not cut away the break-off edge as it serves as a hinge so that the tree does not fall uncontrollably.
- Page 20 Cutting the branches of a fallen tree (C4) First, check which side of the branch is curved. Make the initial cut on the bent side and end by sawing on the opposite side. Cutting an upright branch (C5) First make a cut from the bottom up, then finish with a cut from the top down.
- Page 21 Use a recommended spark plug. The replacement spark plug should be of the same type as the included spark plug of the manufacturer. Guide bar of the chain When removing the chain bar (13), remove the sawdust on the bar and the lubrication opening.
-
Page 22: Storage And Transport
especially on the coupling handle and chain bar. If you find any errors, you must correct them before using the device again. Storage and transport Keep the device in a dry place out of the reach of children. Before storing for a longer period of time, it is advisable to empty the fuel tank and chain oil. -
Page 23: Specifications
Specifications Model: GMC4110 Engine type: 2-stroke Engine volume: 40.1 cm Engine cooling: Air-cooled Engine power 1,4 kW Rotation speed: 2.700 - 12.000 min Oil and fuel mixture: 40:1 (2.5%) - oil for two-stroke engine Fuel tank capacity: 310 ml Oil tank capacity:...