Advertisement
Quick Links
Specifications and operating instructions of Bluetooth wireless microphone J10 / j11
Specification parameters 规格参数
传输协议 transport protocol
传输距离 transmission distance
一拖二 One drag two
耳机监听 Earphone monitoring
降噪 noise reduction
混响 reverberation
声音延时 Sound delay
麦克风 Microphone
频率响应 frequency response
采样率 sampling rate
信噪比 Signal to noise ratio
工作电流 Working current
关机电流 ShutDown Current
续航时间 Endurance time
充电仓电池 Charging bin battery
充电仓输入电压 Charging bin input
voltage
充电仓电池过温保护 Battery over
temperature protection of charging bin
适配器 Adapter
工作温度 working temperature
蓝牙版无线麦克风 J10/J11 规格及操作说明
Support (one for two, without battery compartment
Support (suitable for type-C connector headphones)
支持三级降噪 Support three-level noise reduction
5V-20V（支持快充高耐压输入） 5v-20v (support fast
支持 NTC 功能（充电 0℃～45℃；放电-10℃～60℃）
Support NTC function (charge 0 ℃ ~ 45 ℃; discharge -
发射器 Launcher
蓝牙协议
Bluetooth protocol
≥10 米
支持（一拖二暂时不配电池仓）
temporarily)
支持（适配 TYPE-C 接口耳机）
支持 support
≤25ms
-38dB±3dB 全指向电容咪
-38dB ± 3dB omnidirectional capacitance
20Hz-20KHz
44.1KHz
≥70dB
≤12mA
≤20uA
300mA/H
charging and high withstand voltage input)
10 ℃ ~ 60 ℃)
5V/1A
-10℃-50℃
≥ 10m
6H
Advertisement
Summary of Contents for Hayner-Seek J10
- Page 1 Specifications and operating instructions of Bluetooth wireless microphone J10 / j11 蓝牙版无线麦克风 J10/J11 规格及操作说明 Specification parameters 规格参数 传输协议 transport protocol 蓝牙协议 Bluetooth protocol 传输距离 transmission distance ≥10 米 ≥ 10m 支持（一拖二暂时不配电池仓） 一拖二 One drag two Support (one for two, without battery compartment temporarily) 支持（适配...
- Page 2 按键 Key LED 状态 LED status 备注 remarks 开机 按键 3S 开机 红绿交替闪烁 Power on Press 3S to start Flashing red and green 关机 按键 3S 关机 所有灯灭 Shut down Press button 3S to shut down All lights off 未连接 红绿交替闪烁...
- Page 3 It cannot be started when the voltage is lower than 3.2V 接收器 receiver 无按键 No key LED 状态 LED status 备注 remarks 插入手机端口上电开机 开机 Plug in the mobile phone 红灯闪烁 Red light flashing Power on port and power on 拔出手机端口断电关机 关机...
- Page 4 FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Need help?
Do you have a question about the J10 and is the answer not in the manual?
Questions and answers