Bauer 23503E-B, 59429 - 1000 CFM, 1/5 HP Floor Blower Manual

RULES FOR SAFE OPERATION

1. 
   To reduce the risk of fire or electric shock, do not use this Blower with any solid-state speed control device.
2. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
3. Do not leave Blower running while unattended.
4. Do not operate any blower with a damaged cord or plug. Discard blower or return to an authorized service facility for examination and/or repair.
5. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
6. Never insert fingers, pencils, or any other object through Front or Rear Blade Guards.
7. Disconnect Blower when moving it from one location to another.
8. Disconnect Blower before removing grills for cleaning.
9. Be sure blower is on a stable surface when operating to avoid overturning.
10. DO NOT use blower in window. Rain may create electrical hazard.
11. Complete the assembly of the blower before switching on the blower.
12. Maintain labels and nameplates on the Blower. If unreadable or missing, contact Harbor Freight Tools for a replacement.
13. Use only in dry areas. Do not use in bathrooms, laundry area, near sinks or other sources of water.
14. This Blower is not a toy. Keep it out of reach of children.
15. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure.
16. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all conditions and situations that may occur. It must be understood by operator that common sense and caution are factors which cannot be built into this Blower, but must be supplied by operator.

	This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
	Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
	Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
	Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
	Addresses practices not related to personal injury.

Specifications

FOR COMMERCIAL USE

Functions

Operation

Read the ENTIRE RULES FOR SAFE OPERATION section at the beginning of this manual including all text under subheadings therein before set up or use of this Blower.

1. Set the Power/Speed Switch to the 'OFF' position.
2. Plug the Power Cord into a grounded GFCI-protected outlet.
3. Place the Blower on a level, firm base and position it as needed:
   1. Horizontal
      
      
   2. Tilted 15°
      
      
   3. Tilted 45°
      
      
   4. Vertical 90°
      

User Servicing Instructions

Procedures not specifically explained in this manual must be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION OR ELECTRIC SHOCK:
Turn the Power/Speed Switch of the Blower off, unplug the Blower from its electrical outlet, and allow the Blower to cool completely before performing any inspection, maintenance, or cleaning procedures.

TO PREVENT SERIOUS INJURY FROM BLOWER FAILURE:
Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.

1. BEFORE EACH USE, inspect the general condition of the Blower. Check for:
   • loose hardware,
   • misalignment or binding of moving parts,
   • cracked or broken parts,
   • damaged electrical wiring, and
   • any other condition that may affect its safe operation.

2. Clean outside housing regularly to prevent dust from accumulating in the air inlets/outlet. Use damp cloth during cleaning and dry before use. Do not open housing for cleaning or any other reason.
3. 
   TO PREVENT SERIOUS INJURY: If the supply cord of this Blower is damaged, it must be replaced only by a qualified service technician.

If Blower suddenly stops operating

The Overload Protection may have tripped. Before pressing the Circuit Breaker Reset Button and continuing to use the Blower, make sure:

• that the Blower is dry,
• that the air inlets/outlet are not obstructed, and
• that the Blower has cooled completely.

PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Parts List and Diagram