Technical Data; Before Starting The Equipment - EINHELL TC-DS 20 E Original Operating Instructions

4. Technical data

Mains voltage: ........................ 220-240 V ~ 50 Hz
Power consumption: .................................. 200 W
Idling speed: ...........................12000-22000 min
Sanding/grinding area: .............. 90 x 90 x 90 mm
Oscillatory circuit: ........................................ 2 mm
Protection class: ...........................................II /
Weight: .......................................................1.0 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ........................ 83 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 94 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Handle
Vibration emission value a
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
Anl_TC_DS_20_E_SPK13.indb 14 Anl_TC_DS_20_E_SPK13.indb 14
-1
= 9.8 m/s
2
h
2
- 14 -
GB
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Fastening the grinding/sanding paper
(Fig. 2)
The hook-and-loop fastener enables easy chan-
ging. Make sure that the vacuum extraction holes
on the grinding/sanding paper and the grinding/
sanding disk are aligned.
5.2 Swiveling the grinding/sanding plate
(Fig. 3 / Item 2)
By swiveling the grinding/sanding plate (2) you
can start working again more quickly when any
corners of the grinding/sanding paper or the grin-
ding/sanding plate are worn.
1. Open the grinding/sanding plate lock (1).
2. Swivel the grinding/sanding plate (2).
3. Close the grinding/sanding plate lock (1).
5.3 Fitting the dust extractor adapter
(Fig. 4-6 / Item 3)
1. Press on one side of the cap for the dust ext-
raction opening (4).
2. Remove the cap for the dust extraction ope-
ning (4) from the other side.
31.01.2023 09:21:41 31.01.2023 09:21:41