Viessmann 5085 Operation Manual page 4

2. Introduction
This LED model uses SMD LEDs to produce light matching the
lamp model. Low heat build-up and power input. Nearly unlim-
ited lifetime of the LEDs, so no more change is required.
3. Mounting
- Remove the LED model carefully from the package.
- Check function before mounting.
- Drill a hole (Ø 4 mm) at the mounting place (see fig. 1).
- Put the cables from outside through the hole and push the
socket into the hole. If necessary, fasten the LED model with
the retaining ring from inside (optional).
Caution:
Never touch the mast but only the base socket (fig. 3).
4. Connection
Caution:
Resistor and diode at the cables are needed for proper
function of the LED model. Never cut them off! Never cover
resistor or diode with insulation material, because they have
to be cooled by surrounding air!
While connecting the cables, leave a loop of about 2 – 3 cm
length below the LED model, so that you can pull and reverse
the LED model from the mounting hole during any work.
Connect the LED model to the lighting power output of a model
train transformer (e. g. item 5200) or power supply as shown
in fig. 4 and/or 5.
DC voltage: Connect the diode (red part with black mark)
with the plus pole of the power supply, the resistor with the
minus pole.
AC voltage: Operation with AC voltage could cause some flickering.
We recommend to use the Viessmann power module, item 5215,
which is sufficient for approx. 100 LED lamps or reflectors (fig. 5). Con-
nect the cable to the diode with the brown output socket, the resistor
with the red output socket of the power module.
5. Warranty
Each model is tested to its full functionality prior to delivery. The
warranty period is 2 years starting from the date of purchase.
Should a fault occur during this period please contact our
service department (service@viessmann-modell.com). Please
send the item to the Viessmann service department for check-
ing and repair only after consultation. If we find a material or
production fault to be the cause of the failure, the item will be
repaired free of charge or replaced. Expressively excluded from
any warranty claims and liability are damages of the item and
consequential damages due to inappropriate handling, disre-
garding the instructions of this manual, inappropriate use of the
model, unauthorized disassembling, construction modifications
and use of force, overheating and similar.
6. Technical data
Operating voltage:
Operating current:
FR
Änderungen vorbehalten. Keine Haftung für Druckfehler und Irrtümer.
Die aktuelle Version der Anleitung finden Sie auf der Viessmann Homepage
unter der Artikelnummer.
Subject to change without prior notice. No liability for mistakes and printing
errors.
You will find the latest version of the manual on the Viessmann website using
the item number.
4
(with and without item 5215, power modul)
Entsorgen Sie dieses Produkt nicht über den (unsortierten)
Hausmüll, sondern führen Sie es der Wiederverwertung zu.
Do not dispose of this product through (unsorted) domestic
waste, supply it to recycling instead.
Viessmann
Bahnhofstraße 2a
D - 35116 Hatzfeld-Reddighausen
info@viessmann-modell.com
+49 6452 9340-0
www.viessmann-modell.de
13 – 24 V digital signal
FR
Cet modéle
se recycle
Modelltechnik GmbH
10 – 16 V AC ~
14 – 24 V DC =
ca. 10 mA
À DÉPOSER
EN MAGASIN
Points de collecte sur www.quefairedemesdechets.fr
Made in Europe
Stand 13/sw
À DÉPOSER
EN DÉCHÈTERIE
OU
92889
04/2023
Ho/Kf