Advertisement
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
NOTICE: | Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury. |
Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury. | |
Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superfi cial injury. |
Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not attempt disassembly, use with incompatible components or augment product in any way without the approval of Horizon Hobby, Inc. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
Replace the transmitter batteries when the power LED fl ashes and the transmitter beeps.
MLP6DSM Binding Procedure | |
| |
| |
| |
| |
| |
| |
| |
|
* The trigger switch may also be used for the binding procedure.
If you encounter problems, obey binding instructions and refer to the troubleshooting guide for other instructions. If needed, contact the appropriate Horizon Product Support office.
When pressed down, trim buttons make a sound that increases or decreases in pitch at each pressing. The middle or neutral trim position is heard as a middle tone in the pitch range of the sounds. The end of the control range is sounded by a series of beeps.
A | B | C | D | E | F | G | H | |
Mode 1 | Power LED/ flight mode indicator | Aileron (Left/Right) Throttle (Up/Down) | Throttle Trim | Aileron Trim | ON/OFF Switch | Rudder Trim | Elevator Trim | Rudder (Left/Right) Elevator (Up/Down) |
Mode 2 | Power LED/ flight mode indicator | Aileron (Left/Right) Elevator (Up/Down) | Elevator Trim | Aileron Trim | ON/OFF Switch | Rudder Trim | Throttle Trim | Rudder (Left/Right) Throttle (Up/Down) |
Change flight modes by moving the three-position flight mode switch. Ensure the flight mode switch is in the desired position before flying.
When powered on, this transmitter is automatically in high-rate mode. Change rates by pressing and releasing the right control stick.
Transmitter Model | Type | Reverse Setup | Mode Setup | Switch Positions | Camera Operation | Dual Rate Switch | High Rate | Low Rate |
MLP6DSM | N/A | N/A | N/A | Channel 5 (0) = Stability Mode, Low Angle | Still Mode(Default) Press Trainer = Take Picture Video Mode Press Trainer = Start/Stop Recording Press & Hold Trainer for 4 Seconds = Change Modes | Rate | 100% Fixed | 70% Fixed |
Channel 5 (1) = Stability Mode, High Angle | ||||||||
Channel 5 (2) = Agility Mode |
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download E-FLITE MLP6DSM, EFLRMLP6, EFLRMLP61 - Transmitter Manual
Advertisement
Need help?
Do you have a question about the MLP6DSM and is the answer not in the manual?
Questions and answers