Page 3
Please turn to the final page for tool kit checklist...
Page 5
If you find typographical / textual errors, or you just have a suggestion for us, please feel free to let us know by email at letstalk@c3strom.com. We will offer a coupon as a token of gratitude to you. We really appreciate your feedback! We always look forward to seeing your photos or videos on Instagram, Facebook and Twitter.
Page 7
User Manual ASTRO DELUXE Thank you for purchasing this C3STROM e-bike.
Page 9
Please consult your dealer for service and technical support. You can find more information about our products or find a dealer via www.c3strom.com. If you lack assembly experience, we recommend you seek assembly services from your local ebike shop or dealer. Proper assembly and safe riding are essential.
1.3. PAS & Throttle Due to the powerful support of the motor, the rider will approach high speeds much faster than when riding a conventional bicycle. To get used to this effect, and for your safety, we advise you to first use the e-bike in a familiar setting without too much traffic in the surrounding area, when driving it for the first time.
2. Assembly 2.1. What’s in the box Fully wrapped C3STROM ASTRO DELUXE with foam and cardboard...
Page 17
2.1. What’s in the box Keys 13 / 15 mm Double Wrench 13 / 15 mm Double Wrench User Manual Pedal L Pedal R 10 / 13 mm Double Wrench 5 mm Allen Wrench 4 mm Allen Wrench Charger Cable Charger 2.5 mm Allen Wrench Toolbox...
2.2. Assembly Process Place the carton box upside down, and remove the 4 safe buckles to lift the cover up.
Page 19
2.2. Assembly Process Please loosen the front wheel.
Page 20
Loosen the screws using the 4mm Remove the display from the handle- Allen wrench and take the cap off bar, please take care that the screws do here. not fall off. Loosen the screws with the 2.5mm Attach the handlebar and tighten the Allen wrench.
Page 21
Snap the display back onto the Use the two 13 / 15 mm wrenches handlebar and tighten the screw with (both on the 15 mm side) to undo the the 2.5mm Allen wrench. bolts attached at either end. Make the correct connections Remove the Axle and spacer and between the display and the wires.
Page 22
Remove the plastic spacer nestled Please take the screw nut of the Axle between the brake pads on the front off as shown in the picture and insert it fork of the wheel. into the hole in the middle of the wheel.
Page 23
Turn the wheel over and tighten Place the front fork onto the the screw. wheel. NOTICE: Please leave some space for further Make sure it's placed on that part that was tightening after following the next steps. tightened.
Page 24
13 . Use the two 13/15 mm wrenches at the Place the fender between the same time (both on the 15 mm side) to front wheel and the front fork. (As the tighten the screws. picture shows) Put the screw through the hole on the front fork and the lifting eye on the fender.
Page 25
Use the 5mm Allen wrench to Insert the two turn signals into keep the screw in place and tighten the locations shown below, then the screw using the 8/10mm double tighten the screws and connect the wrench (the 10mm side). turn signal wire connectors.
Page 26
Use the two 13 / 15 mm wrenches Fix the headlight to a suitable (both on the 15 mm side) to undo the height. bolts attached at either end of the skewer on the wheel. Lift the headlight up to the suitable Identify the left and right sides of position.
Page 27
Insert the pedals into the holes of the crank on each respective side, and tighten the right side clockwise and the left side counterclockwise with the 15mm side of the 13/15 mm wrench.
3.2. Finger-tip Control Please press the on/off button before use the HB/LB function. Slide button to use turn signal. (Press to turn on left signal, press to turn on right signal) Error Alert Assisted Pushing Bluetooth Battery Level Headlight Battery Level Percentage Cruise Motor Power...
Page 30
Display Operating Instructions Assistance Level Power on / off to change the assis- Press for 1 second to turn the tance level. There are 6 modes: device on when the connection is 0/1/2/3/4/5. stable. To turn it off, press for 1 second.
Page 31
NOTICE: Display Error Code 1. Error code0x04: Throttle not reset. Verify the proper positioning of the throttle 2. Error code0x05: Throttle malfunction. Inspect the throttle. 3. Error code0x07: Overvoltage protection. Verify the battery voltage. 4. Error code0x08: Motor Hall signal wire Examine the motor module.
4.2 Battery Charging Open the charging port. Connect the charger. 3 Green 1Red 100% 2 Green 1Red 1 Green 1Red 0 Green 1Red Battery charging indicator light will You can now view the power turn on. display.
The charger is expected to become relatively warm while charging. If the charger becomes too hot to ● touch, please unplug the charger instantly. If you notice any signs of overheating, stop using the charger and contact C3STROM support. ●...
Thank you for follow instructions is not covered under warranty and could your understanding and cooperation! result in serious injury or death. Contact C3STROM if you have any questions about assembly or operation.
If you do not have the experience, skill, and tools to complete maintenance and adjustment of the bike on your own, C3STROM strongly recommends having a certified, reputable bike mechan- ic maintain, tune, and ensure the bike is safe to ride.
7. Warranty The specific warranty covering your C3STROM bike is governed by the law of the state or country in which it was purchased. It applies only to bicycles purchased from C3STROM or authorized retailers. If you believe your C3STROM bike has an issue covered by warranty, your first point of contact should be the place where you purchased your e-bike.
Normal wear and tear of any ‘Covered Component’. ● C3STROM will not be liable and/or responsible for any damage, failure or loss caused by ● any unauthorized service or use of unauthorized parts.
Shipping damage claims are extremely time sensitive. It is your responsibility to immedi- ately inspect the e-bike for damage upon receipt. Damage to a ‘Covered Component’ during shipping is not covered by this Limited Warranty. However, C3STROM will replace such damaged ‘Covered Components’ if you: Notify C3STROM of a Covered Component damaged in the shipping process within ●...