Table of Contents
Advertisement
Available languages
Available languages
3.1
1.
Place the device on a solid and flat surface for use to ensure that it
cannot tip over or fall down.
Positioning
2.
Position the device about 40 - 50 cm away from your head, for exam-
and setup
ple on a bedside table.
3.
Plug the cable antenna to the the connector for cable antenna
the rear side of the device.
4.
Plug the mains cable end to the connector for power cable
rear side of the device and the power adapter to the wall outlet.
3.2
Press and hold the Set-button
in the display flashes. Adjust the time with the
Setting the
Press the Set-button
time and the
select one of two alarm settings (AL1 or AL2) or the Zizz (short time
alarms
alarm) for adjustment with the
The adjustment needs to be done in the same way with the
and
the way of alarming: By radio (FM) or by nature sounds (Sound).
Depending on your selection you then need to adjust either the radio
frequency or one of the eight nature sounds. In the following you need to
set the volume and the light brightness level. If you only want to use the
light or sound/radio function, adjust the other function to 0.
If you do not press a button for at least 10 seconds, the device will quit
the setting mode automatically. To activate an alarm you need to press
the corresponding button (see 3.6 Activate an alarm resp. 3.7 Short time
alarm). In case an alarm is activated, the L-Mode-
buttons are not available.
3.3
With the S-Mode-button
press on the button you change the source in this sequence: SOUND
Choose the
(nature sounds) - FM (radio) - MPS (MP3 player) - OFF. If you have
source of
chosen the nature sounds, you additionally need to select one of the eight
sound
sounds with the
(S-Mode)
MP3 player with 3.5mm jack plug needs to be connected to the connector
for MP3 player
trolled with the buttons
3.4
By pressing the L-Mode-button
the
Light
The level of brightness increases in increments from 0 to 20. Press the
settings
buttons
(L-Mode)
If you press the L-Mode-button
gradually from setting number to 0, and the
reading, we recommend brightness level 20. Subsequently, the first relax
mode is activated, in which the colour of light changes about every 8
seconds in this sequence: Red - blue - green - red/blue - blue/green -
green/red - red/blue/green. If you press button
activated and the colour of light changes about every 4 hours. Press button
again to switch to the next relax mode in which the colour of light will not
change automatically. Choose the light colour by pressing button
colour) or
relax mode. If you press the L-Mode-button
will be switched off.
0
0
buttons as for the time adjustment. Additionally you need to select
9
►
and
u
and needs to be switched on. The volume can be con-
e
icon appears on the display and the level (0 - 20) of brightness.
6
7
or
to adjust the brightness as desired.
7
(previous colour). The brightness level is not adjustable in
0
for about 3 seconds, until the time
again to confirm the time. After that, you may
9
q
►
◄
,
and
w
you can choose a sound source. With each
q
◄
buttons. For listening to MP3 music, a
r
and
.
8
you activate the luminous element
8
a second time, the light darks down
8
a third time, all light functions
3 Operation
z
9
q
►
◄
and
buttons.
0
buttons.
9
►
,
8
and S-Mode-
icon disappears. For
6
the next relax mode is
6
GB
G
G
i
on
G
on the
G
q
◄
w
g
2
,
G
(next
11
Advertisement
Table of Contents
