Anleitung -
Schraubensatz -
Screw set -
11x
4x
4x
M3x12
M3x8
1
Montage: Legen Sie die Hardware auf eine antistatische
Unterlage. Beginnen Sie mit der Demontage des Original-
Kühlers. Je nach Aufbau des Kühlers sind zuerst die
Schrauben des Lüfters zu entfernen und die Blenden zu lösen.
Bei aufgeklebten Kühlern ist äußerste Sorgfalt geboten.
Es können leicht Bauteile abgerissen werden. Heben Sie
alle Einzelteile sorgfältig auf. Reinigen Sie anschließend die
Hardware von Resten der Wärmeleitpaste oder
Pads mit einem Lösemittel (z.B. Spiritus).
2
Tragen Sie nun, unter Zuhilfenahme eines Plastikstreifens
oder Ähnlichem, eine gleichmäßige Schicht Wärmeleitpaste
auf die zu kühlende GPU auf. Die Schicht sollte weniger als
einen Millimeter dick sein, da sonst die umliegenden Bauteile
unnötig verunreinigt werden können.
3
Entfernen Sie die Schutzfolie der rot dargestellten 15 mm x 15
mm x 1,5 mm Wärmeleitpads und legen Sie diese auf die
Speicherbausteine. Die orangenen 15 mm x 15 mm x 2 mm
Pads werden auf den Spannungswandlern platziert.
Vergessen Sie nicht, auf beiden Seiten, die Schutzfolie zu
entfernen. Die übrigen orangen und roten Wärmeleitpads für
die Spannungswandler müssen erst zugeschnitten werden.
Die genauen Maße entnehmen Sie bitte der
Schnittmustervorlage, am Ende der Anleitung. Schneiden Sie
auch die gelb dargestellten Wärmeleitpads zu und platzieren
Sie diese, wie auf dem Bild gezeigt, auf der Platine. Beachten
Sie, dass diese genau gegenüber der Spannungswandler auf
der Rückseite liegen. Vergewissern Sie sich, dass Sie alle
Schutzfolien entfernt haben.
GPX-A 390-M02
Instruction manual -
Jeu de vis
2x
16x
15mm x 15mm x
1,5mm
SW 2 / SW 2,5
1x
3x
30mm x 30mm x
15mm x 15mm x
1,5mm
2mm
Assembly: Put the hardware on an antistatic mat. Start with
the dismantling of the original cooler. Depending on the
structure of the cooler remove the screws at the back of the
card and carefully unhook the fan connector. If the original
cooler uses thermal glue extreme care should be taken. As you
can easily damage parts. Pick up all the items carefully. Then
clean the hardware of thermal paste or pad residues with a
solvent (eg. alcohol).
With the help of a plastic strip or thermal paste spreader make
a thin layer of thermal paste on the GPU. The layer should be
less than a millimeter thick, otherwise the surrounding
components can be contaminated unnecessarily.
Remove the protective films of the 15 mm x 15 mm x 1.5 mm
thermal pads in red and place them on the memory chips. The
orange 15 mm x 15 mm x 2 mm pads are placed on the voltage
transformers. Do not forget to remove the protective films on
both sides. The remaining orange and red thermal pads for the
voltage transformers must be cut to size. For the exact
dimensions please see the cutting template, at the end of the
manual. Cut the yellow thermal pads and place them on the
board as shown in the picture. Note that these lay on the rear
side of the voltage transformers on the back. Make sure that
you removed all protective films.
Instructions de service
1x
19x
30mm x 30mm x 2mm
15mm x 15mm x
3mm
Assemblage: Insérez le matériel sur un tapis antistatique.
Commencez par le démantèlement du refroidisseur d'origine.
En fonction de la structure du radiateur est de retirer les vis de
fixation du ventilateur pour retirer et régler l'ouverture. Lorsque
refroidisseurs collés soin extrême doit être exercé. Il peut
facilement être déchiré parties. Ramassez tous les articles
soigneusement. Ensuite, nettoyer le matériel de résidus de la
pâte thermique ou de tampon avec un solvant (alcool).
Porter les maintenant à l'aide d'une bande de matière plastique
ou analogue, une couche uniforme de pâte thermique à la GPU
à refroidir. La couche doit être inférieure à un millimètre
d'épaisseur, faute de quoi les composants environnants
peuvent être contaminés inutile.
Enlevez les films protecteurs de les rouges 15 mm x 15 mm x
1,5 mm pads thermiques et placer les sur les puces de
mémoire. Les orange 15 mm x 15 mm x 2 mm pad sont placés
sur les transformateurs de tension. Ne pas oublier d'enlever les
films protecteurs sur les deux côtés. Les pads thermiques
orange et rouge restantes pour les transformateurs de tension
doivent être coupés. Pour les dimensions exactes s'il vous plaît
voir le gabarit de découpe, à la fin du manuel. Coupez les pads
thermiques jaunes et le placer les sur la carte
dans
l'image. Notez que ceux-ci sont placés sur le côté arrière
des convertisseurs de tension. Assurez-vous que vous avez
enlevé toutes les films protecteurs.
1
1x
2x
30mm x 30mm x
3mm
comme indiqué
Need help?
Do you have a question about the GPX-A 390-M02 and is the answer not in the manual?
Questions and answers