Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Diamond G17/PR4T-N
Summary of Contents for Diamond G17/PR4T-N
- Page 1 10/2011 Mod: G17/PR4T-N Production code: 373030...
-
Page 2: Table Of Contents
INDEX I. COMBINING APPLIANCES / TABLES ....................2 II. DATAPLATE and TECHNICAL DATA ....................16 III. GENERAL INSTRUCTIONS ....................... 17 IV. THE ENVIRONMENT .......................... 18 1. PACKING ............................. 18 2. USE .............................. 18 3. CLEANING ............................18 4. DISPOSAL ............................18 V. -
Page 3: Dataplate And Technical Data
II. DATAPLATE and TECHNICAL DATA Important This manual contains information relevant to various appliances. See the appliance dataplate located under the control panel in order to identify the appliance (see fig. above). TABLE A - Gas appliance technical data MODELS +7FTGDHS00 +7FTGDSR00 +7FTGDCS00... -
Page 4: General Instructions
III. GENERAL INSTRUCTIONS • Carefully read the instruction handbook before using the appliance. • After installation keep the instruction handbook for future consultation. • FIRE HAZARD - Keep the area around the appliance clear and free from combustible materials. Do not keep flammable materials in the vicinity of the appliance. -
Page 5: The Environment
IV. THE ENVIRONMENT V. INSTALLATION • Carefully read installation 1. PACKING maintenance procedures given in this instruction Packing materials are environment friendly and can manual before installing the appliance. be stored without risk, or burned in a special waste • Installation, maintenance and conversion to another type incineration plant. -
Page 6: Connections
3.1. COMBINING APPLIANCES 5. CONNECTIONS • (Fig.1A) Undo the 4 fixing screws and remove the control panels • Any installation or maintenance work on the of the appliances. feed system (gas, electricity) must only be carried • (Fig.1B) Remove the fixing screw nearest the control panel, from out by the utility company or an authorised each side to be joined. - Page 7 5.1.4 GAS PRESSURE REGULATOR 5.1.6.1 REPLACING THE MAIN BURNER NOZZLE If the gas pressure is higher than that specified or is difficult (all versions) to regulate (not stable), install a gas pressure regulator • Unscrew nozzle “C” and replace it with the corresponding (accessory code 927225) in an easily accessed position nozzle for the selected gas (Table B, fig.3B) complying ahead of the appliance.
-
Page 8: Safety Thermostat
5.2. ELECTRIC APPLIANCES 5.2.1. ELECTRICAL CONNECTION (Fig. 4A-Table C). IMPORTANT! Before making the connection, check the compatibility of the dataplate specifications with the mains voltage and frequency. • To access the terminal board, remove the control panel of the appliance by removing the fixing screws (fig. 4A 1-2). •... -
Page 9: Instructions For The User
Switching on VI. INSTRUCTIONS FOR THE Lighting the pilot flame USER • Press and turn knob “A” from “off” to “pilot on”. • Press down knob “A” and at the same time press piezoelectric switch “B” repeatedly, which will light the pilot flame. Check 1. -
Page 10: Cleaning
Switching off the fry-top with valve VII. CLEANING • Turn knob “A” to “pilot ignition” to turn off the main burner. • To shut off the pilot, press the knob “A” lightly and turn it to “off”. IMPORTANT! At end of service: Before carrying out any cleaning operation, disconnect the •... -
Page 11: Periods Of Disuse
Important: do not use the edge scraper (see figure) VIII. MAINTENANCE 1. MAINTENANCE All the components requiring maintenance are accessible from the front of the appliance, after removing the control panel and front panel. Disconnect the power supply before opening the appliance 1.1 BRIEF TROUBLESHOOTING GUIDE Even with nor mal appliance use, malfunctions can occasionally occur. - Page 12 INSTRUCTIONS REPLACING COMPONENTS (to be carried out only by a specialised installer) GAS VALVE/COCK • Remove the knobs and control panel. • Unscrew the pilot and thermocouple pipe. • Unscrew the gas inlet and outlet connections. • Lift the cooking plate at the front and remove the thermostat bulb.