Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Acer ConceptD CT300-52A i7-11700
Summary of Contents for Acer ConceptD CT300-52A i7-11700
- Page 1 Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Acer ConceptD CT300-52A i7-11700 / 16GB / 1TB / Windows 10 Pro o cerca il tuo prodotto tra le migliori offerte di PC Desktop e Workstation ConceptD 300...
- Page 2 Images provided herein are for reference only and may contain information or features that do not apply to your computer. Acer Group shall not be liable for technical or editorial errors or omissions contained in this manual.
-
Page 3: Table Of Contents
Table of Contents Memory ............11 UPGRADING YOUR COMPUTER ..... 1 Memory configuration Installation precautions ....1 guidelines ..........11 ESD precautions ........ 1 Removing a memory module . 12 Required tools ........1 Installing a memory module ... 13 Pre-installation instructions .. - Page 4 - UPGRADING YOUR COMPUTER Upgrading your Computer In this section, you will find: • Instructions on how to replace a hardware component...
-
Page 5: Upgrading Your Computer
UPGRADING YOUR COMPUTER - UPGRADING YOUR COMPUTER Installation precautions Before you install any computer component, we recommend that you read the following sections. These sections contain important ESD precautions along with pre-installation and post-installation instructions. ESD precautions Electrostatic discharge (ESD) can damage your processor, disk drives, expansion boards, and other components. -
Page 6: Pre-Installation Instructions
- UPGRADING YOUR COMPUTER Pre-installation instructions Always observe the following before you install any component: Make sure that the ODD and card reader slot is empty. Turn off the power to the computer and all peripherals. Unplug the power cord from the computer. Unplug the network cable and all connected peripheral devices from the computer. -
Page 7: System Upgrade
UPGRADING YOUR COMPUTER - System Upgrade Removing the rear system cover Before you proceed, make sure that you have turned off your computer and all peripherals connected to it. Read the Pre-installation instructions on page Remove the screw that secure the rear system cover to the computer. -
Page 8: Installing The Rear System Cover
- UPGRADING YOUR COMPUTER Installing the rear system cover Align the cover to the bottom part of the computer’s rear side (1). Push the rear system cover until it latches into place (2). Secure the rear system cover to the computer using one screw. -
Page 9: Removing The Left Side System Cover
UPGRADING YOUR COMPUTER - Removing the left side system cover Before you proceed, make sure that you have turned off your computer and all peripherals connected to it. Read the Pre-installation instructions on page Remove the two screws that secure the left side system cover to the computer (1). -
Page 10: Installing The Left Side System Cover
- UPGRADING YOUR COMPUTER Installing the left side system cover Align the cover to the sides of the computer and slide the cover toward the front of the computer (1). Secure the cover with two screws (2). Observe the Post-installation instructions on page... -
Page 11: Hard Drives
UPGRADING YOUR COMPUTER - Hard drives The computer supports installation of two 3.5-inch SATA hard drives in the internal HDD cage. Removing the 3.5-inch hard drives Perform the Pre-installation instructions on page Disconnect the power (1) and data (2) cables from the hard drives. - Page 12 - UPGRADING YOUR COMPUTER Pull both sides of the HDD carrier (1) then remove the hard drive (2).
-
Page 13: Installing The 3.5-Inch Hard Drives
UPGRADING YOUR COMPUTER - Installing the 3.5-inch hard drives Remove the new hard drive from their packaging. Place the hard drive into the carrier (1) and reinsert the retaining screws into the hard drive (2). Insert the hard drives into the chassis. - Page 14 - UPGRADING YOUR COMPUTER Connect the power (1) and data (2) cables to the hard drives. Observe the Post-installation instructions on page...
-
Page 15: Memory
The computer has four DDR4 U-DIMM slots that support up to 64 GB maximum system memory. Memory configuration guidelines To ensure data integrity, use only Acer-approved DDR4 3200 MHz type memory modules. Memory modules must be installed starting with DIMM1 slot. -
Page 16: Removing A Memory Module
- UPGRADING YOUR COMPUTER Removing a memory module Perform the Pre-installation instructions on page Remove the graphics board. See Removing the graphics board on page Press outward the holding clips on both sides of the DIMM slot outward to release the memory module (1). Gently pull the memory module upward to remove it from the DIMM slot (2). -
Page 17: Installing A Memory Module
UPGRADING YOUR COMPUTER - 13 Installing a memory module Note DIMM slots on the mainboard must be installed only in certain configurations. Numbers next to DIMM slots correspond to installation sequence. Be sure to install the memory module in DIMM1 slot followed by DIMM2 slot. Select an empty DIMM slot. -
Page 18: Graphic Board
- UPGRADING YOUR COMPUTER Graphic board The computer contains one or two Graphic boards installed in the PCIE x16 slots. The detail configuration will be differed by different models. Removing the Graphics board Perform the Pre-installation instructions on page Disconnect the power cables from the graphics board. Remove the three screws that secures the graphics board to the chassis. - Page 19 UPGRADING YOUR COMPUTER - 15 Unlatch the metal clip that secure the graphics board to the chassis. Release the latch that secures the graphics board to the mainboard (1). Detach the graphics board from the PCIE x16 slot (2).
-
Page 20: Installing The Graphics Board
- UPGRADING YOUR COMPUTER Installing the Graphics board Remove the new graphics board from its packaging. Insert the graphics boards into the PCIE x16 slot and press it down until it latches into place. Note For replace/upgrade graphic board, please check the specification of graphic board &... - Page 21 UPGRADING YOUR COMPUTER - 17 Secure the graphics board to the chassis using three screws. Connect the power cables to the graphics board. Observe the Post-installation instructions on page...
-
Page 22: M.2 Ssd Module
- UPGRADING YOUR COMPUTER M.2 SSD module The computer contains one M.2 SSD module installed in the M.2 PCIE slot. Removing the M.2 SSD module Perform the Pre-installation instructions on page Remove the graphics board. See Removing the graphics board on page Remove the screw that secures the M.2 SSD module from the mainboard. - Page 23 UPGRADING YOUR COMPUTER - 19 Remove the thermal pad from the SSD module.
-
Page 24: Installing The M.2 Ssd Module
- UPGRADING YOUR COMPUTER Installing the M.2 SSD module Remove the new M.2 SSD module from its packaging. Place a thermal pad into the SSD module. Insert the M.2 SSD module into its slot in the mainboard. - Page 25 UPGRADING YOUR COMPUTER - 21 Secure the M.2 SSD module to the mainboard using one screw. Replace the graphics board. See Installing the graphics board on page Observe the Post-installation instructions on page...
- Page 26 - CONCEPT D PALETTE ConceptD Palette In this section, you will find: • Information on how to use the ConceptD Palette software...
-
Page 27: Concept D Palette
App Center Creative Tools Settings To set up the ConceptD Palette application (Windows 10): From the Start menu, select All apps. Select Acer. Select ConceptD Palette. Alternatively, you can double-click the ConceptD Palette desktop shortcut to run the application. -
Page 28: Monitoring
- CONCEPT D PALETTE Monitoring Select the Monitoring tab to view CPU, GPU and system performance. Category Description Displays CPU temperature and loading. Displays GPU temperature and loading. Displays temperature and loading. System Also displays RAM, Wi-Fi and LAN usage. -
Page 29: Split Screen
CONCEPT D PALLETE - 25 Split Screen Select the Split Screen tab to configure your screen display. Category Description Shows options on various split screen Split Screen configurations. -
Page 30: App Center
- CONCEPT D PALETTE App Center Select the App Center tab to view the applications that are avilable for quick access. You can add frequently used applications to this tab by clicking the “+” sign. Category Description Displays applications available for App Icon quick access/executions. -
Page 31: Creative Tools Settings
CONCEPT D PALLETE - 27 Creative Tools Settings Select the Creative Tools Settings tab to configure frequently used design tools. Category Description Screen Snip Settings Configure screen snip setting options. Clipboard Settings Configure clipboard setting options. Color Picker Configure color picker setting options. On-Screen Keyboard Configure on-screen keyboard Shortcuts...