Table of Contents
Advertisement
Installation procedure
1. Carefully read the included leaflet "License agreement for Roland software" and verify
that you accept the conditions.
2. Insert the SETUP DISC into the CD-R/RW drive.
3. Press [CD-RW].
The CD-RW menu screen will appear.
4. Select Page 2 "PLUG-IN Inst," and press [ENTER/YES].
The PLUG-IN INSTALL screen will appear. This shows product information about the VS
plug-in program (manufacturer, product name, plug-in version, and size).
The drive (partition) in which the plug-in program is to be installed will be decided by
the VS series device. The drive information is shown at "DESTINATION" on "PLUG-IN
INSTALL" screen. Check that the remaining capacity of the disk is bigger than the size of
VS plug-in program to be installed. For installation, a remaining capacity of twice or
more than the VS plug-in program size is required.
5. Press [F5 (Instal)].
The "Install?" popup will appear.
6. To begin the installation, press [ENTER/YES].
The "AUTHORIZE?" popup will appear.
7. If you want to install the authorized version, press [ENTER/YES]. If you want to install
the trial version, press [EXIT/NO].
If you press [ENTER/YES], authorization data will be written to the SETUP DISC and the
hard disk, and the program will be installed. If you press [ENTER/NO], a trial version will
be installed but authorization data will not be written.
The "Really, Sure?" popup will appear.
8. To confirm the installation, press [ENTER/YES].
9. When installation is completed, remove the SETUP DISC.
The CD-RW menu screen will appear.
Backing up your VS plug-in programs
If the SETUP DISC becomes lost or damaged after you have used it to install the authorized
version of a plug-in program, you will be unable to re-install (p. 16) the plug-in. As a
safeguard against such problems, we strongly recommend that you back up your VS
plug-in programs on a commercially available CD-R/RW disc after authorization.
Backing up also lets you save the user patches of the plug-in effect to the CD-R/RW disc.
1. Insert a blank CD-R/RW disc into the CD-R/RW drive.
2. Press [CD-RW].
The CD-RW menu screen will appear.
3. Select Page 2 "PLUG-IN Back," and press [ENTER/YES].
The PLUG-IN BACKUP screen will appear. This lists the VS plug-in programs that are
installed on the hard disk.
4. Use the cursor to select the plug-in that you want to back up, and press [F4 (BACKUP)].
The "Backup?" popup will appear.
5. To begin the backing up, press [ENTER/YES].
The "Really, Sure?" popup will appear.
6. To confirm the backing up, press [ENTER/YES].
If you press [ENTER/YES], VS plug-in programs will be backed up to CD-R/RW disc.
The PLUG-IN BACKUP screen will appear.
The contents of the SETUP DISC are recorded in VS format (the dedicated data format of
the VS series). Therefore, it is impossible to make a backup disc on a PC.
If you are unable to install
successfully even when
using a not-yet-authorized
SETUP DISC, please
contact your dealer or a
Roland service center
listed in the "Information"
section of the manual.
If the SETUP DISC is not
yet inserted after Step 6, a
message of "Please Insert
Plug-in CD" will appear,
and the CD-RW drive tray
will open.
The plug-in programs will
be installed in the drive
(partition) that precedes
the last drive. For example
if you have drives
IDE0~IDE3, the programs
will be installed in the
IDE2 drive.
If you lose or damage the
SETUP DISC after
authorization, a fee will be
charged for a correctly
functioning replacement
disc. Be sure to back up
your VS plug-in programs
in order to avoid such an
inconvenience.
It is able to use the
backuped plug-in program
as authorized version if
installed to VS series with
Key Card.
15
Advertisement
Table of Contents
