Table of Contents
Advertisement
Quick Links
LS-3 OWNER'S MANUAL
READ ENTIRE MANUAL BEFORE OPERATION
Always disconnect hoses prior to making adjustments or servicing.
•
Must be 18 years or older to operate the Lane Shark.
•
Never raise the Lane Shark above oorboard height when in the
•
horizontal position.
Keep body and clothing away from all moving parts.
•
Do NOT attempt to change positions or repair the Lane Shark while
•
hydraulic hoses are connected.
Use the machine only for the intended use. Do NOT modify the machine.
•
Do NOT use if any parts are missing or damaged. Follow instructions at all
•
times while operating the Lane Shark. Failure to follow these instructions
could result in serious injury or death.
Important operation and safety instructions can be found
immediately on the internet by scanning these codes with your
Position Change
Safety Video
(850) 610-2870
Lane Shark LS-3 Hydraulic Rotary Cutter
smartphone device's camera.
www.lanesharkusa.com
Hydraulic
Plumbing Video
1
Advertisement
Table of Contents
Summary of Contents for LaneShark LS-3
- Page 1 LS-3 OWNER’S MANUAL Lane Shark LS-3 Hydraulic Rotary Cutter READ ENTIRE MANUAL BEFORE OPERATION Always disconnect hoses prior to making adjustments or servicing. • Must be 18 years or older to operate the Lane Shark. • Never raise the Lane Shark above oorboard height when in the •...
- Page 2 INTRODUCTION Lane Shark LS-3 For future reference, please record all applicable information pertaining to your machine in the table below. If you replace this manual, be sure to transfer ALL information into your new manual. Dealer Information STORE NAME: ___________________________________________________...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Lane Shark LS-3 Safety Information Safety Precautions ..……………………………………………………4 Safety Labels ……………………………………………………..5-7 Introduction General Information ..……………...…………………………………8 Overview ……..…………………………………………………………..9 Components Cutting Deck …….………………………………………………….10-11 Back Plate ..…………………………………………………….12-13 Swing Arm ....……………..………………………………14 Kickstand .……………………………………………………………….15 Rotating Assembly …………………………………………………...16 Motor ……………………………………………………………………..17 Hydraulic Hoses ……………………………………………..……18-19 Blade Carrier ……………..………………………………………….20... -
Page 4: Safety Information
SAFETY INFORMATION Lane Shark LS-3 SAFETY PRECAUTIONS OVERVIEW Throughout this section you will nd various safety precautions and warnings. READ, UNDERSTAND, and FOLLOW ALL safety instructions contained in this section before attempting to operate your machine. This Owner’s Manual is a key part of operational safety and must be maintained with the implement at all times. -
Page 5: Safety Labels
SAFETY INFORMATION Lane Shark LS-3 SAFETY LABELS PLACEMENT Your Lane Shark comes equipped with safety labels in place. DO NOT remove these labels! They are placed to help you operate your machine in a safe manner. Read, understand, and follow their directions. - Page 6 SAFETY INFORMATION Lane Shark LS-3 (850) 610-2870 www.lanesharkusa.com...
- Page 7 SAFETY INFORMATION Lane Shark LS-3 LABEL PLACEMENT CHART (850) 610-2870 www.lanesharkusa.com...
-
Page 8: General Information
O set, directly in front (level), or 25°, 35°, & 45° in the vertical and o set positions. The Lane Shark LS-3 attaches to the front of any FEL tractor with a • SSQA or JD Hook & Pin-Style attachment system. There are adapters available to t most other applications sold separately. -
Page 9: Overview
INTRODUCTION Lane Shark LS-3 OVERVIEW : (11) Mounting Hooks (01) Cutting Deck DELS3000002022A (12) Mounting Pins (02) Backplate BPLS3000002022A (13) Tower Lock (03) Spindle Mounting Plate (14) Blade Carrier (04) Kickstand BCLSS4B0002022A KSLS3000002022A (15) Deck Reinforcement Edge (05) Main Adjustment Hinge... -
Page 10: Cutting Deck
(Facing the unit) The left deck support (A) is supplied with a bracket (C) for the Kickstand (04) to connect once the LS-3 is in the vertical and o set positions. The right deck support (B) is mounted to the Main Adjustment Hinge (05) which allows the LS-3 to pivot into the vertical and o set positions while maintaining attachment to the Mounting Plate (02). - Page 11 COMPONENTS Lane Shark LS-3 01 CUTTING DECK DELS3000002022A ABOVE BACK SIDE BELOW (850) 610-2870 www.lanesharkusa.com...
- Page 12 Deck (01) this allows the Backplate (02) to act as the main support system for the LS-3. (Facing the unit) O set to the left side of the Backplate (02) is a roughly 3 inch Boss pivot pin, this attaches the Swing Arm (06), Kickstand (04), Main Adjustment Hinge (05), Main Arm Support (10), to the Cutting Deck (01) and operates as the Main Pivot Point (07).
-
Page 13: Backplate
Mounting Hooks (11) located on the top left and right sides of the LS-3. Once the Mounting Hooks (11) are attached, the Mounting Pins (12) located on the lower left and right sides of the LS-3 will then lock the LS-3 to the Hook & Pin-Style loader. -
Page 14: Swing Arm
Cutting Deck (01) to the Swing Arm (06) via the Main Adjustment Hinge (05). This allows the LS-3 Cutting Deck (01) to move 180 degrees from directly in front of the tractor to the vertical and o set positions while staying attached to the loader. -
Page 15: Kickstand
KSLS3000002022A The Kickstand (04) attaches to the Main Arm Support (10) once the LS-3 has been locked into any of its positions. This allows the Swing Arm (06) to support the LS-3 when in the vertical and extended positions. (850) 610-2870... -
Page 16: Rotating Assembly
COMPONENTS Lane Shark LS-3 Rotating Assembly (8) Lower Bearing (9) Main Shaft (1) Hydraulic Motor (10) Carrier Mounting Plate (a xed) (2) Bearing Lock Nut (11) Blade Carrier (3) Bearing Lock Washer (12) Cutting Blades (4) Spindle Housing (13) Blade Bolts... -
Page 17: Motor
01 MOTOR MRLS3D00002022A The motor is the main component of the Lane Shark LS-3. The 5.5 GPM Danfoss gear motor is equipped with two #10 ORB (O-Ring Boss) inlets. It is secured to the motor mount via two 1/2-14x1.5” socket caps with a 3/8 head (A) shown in gure 2. -
Page 18: Hydraulic Hoses
Lane Shark LS-3 Hydraulic Hoses The Lane Shark LS-3 requires two hydraulic hoses to operate. (NOT INCLUDED) One for pressure (02) and one for the return (03). To run the Lane Shark, YOU MUST HAVE AUXILIARY HYDRAULICS such as rear remotes, third function, or a Lane Shark valve kit. - Page 19 COMPONENTS Lane Shark LS-3 Hydraulic Hoses To ensure your safety and that no harm is caused the components of your Lane Shark or your tractor, it is CRUCIAL that the hydraulic hose system is installed correctly. You CAN NOT return to the valve powering your Lane Shark.
-
Page 20: Blade Carrier
Reinforcement Edge (15) is a 1/2 inch thick border that covers the front edge of the LS-3. This Deck Reinforcement Edge (15) protects the Cutting Deck (01) from any debris the LS-3 may come in contact with while in operation. BELOW 16.88... -
Page 21: Cutting Blades
Lane Shark LS-3 COMPONENTS Cutting Blades Figure 1 BKLS3000002022A Your Lane Shark is equipped with two 9”x3” double sided cutting blades (B). Each cutting blade is 1/2” thick and is secured to the blade carrier by one 2-1/16”x1-1/8” Rotary Cutter Bolt, one 1-1/8” Split Lock Washer, and one 1-1/8”... -
Page 22: Replacing Blades
COMPONENTS Lane Shark LS-3 Blade Replacement (Refer to Figure 1) Before attempting to replace or ip (double sided) blades make sure you have completed all steps in the “WARNING” section on page 36. Failure to complete these steps could result in serious injury or death. -
Page 23: Safety Checklist
SAFETY CHECKLIST Lane Shark LS-3 (850) 610-2870 www.lanesharkusa.com... -
Page 24: Operating Instructions
OPERATING INSTRUCTIONS Lane Shark LS-3 Mounting DANGER When mounting your Lane Shark a crushing hazard exists. DO NOT allow anyone to stand between or get near the front of the tractor when attaching. Always make sure hydraulic hoses are disconnected before attaching or detaching your Lane Shark. - Page 25 OPERATING INSTRUCTIONS Lane Shark LS-3 Mounting Figure 1 Hook & Pin Style Loader (JD) Mounting Hooks Locking Pins Loader Boom Figure 2 Skid Steer Quick Attach (SSQA) Locking Pins Loader Boom (850) 610-2870 www.lanesharkusa.com...
-
Page 26: Operation
OPERATING INSTRUCTIONS Lane Shark LS-3 OPERATION Tractor Requirements In addition to correct hydraulic ow and horsepower, the tractor must also be properly equipped with operator protection including a Roll Over Protection Structure or (ROPS). Minimum hydraulic ow is 5GPM •... - Page 27 OPERATING INSTRUCTIONS Lane Shark LS-3 OPERATION Cutting Grass or Vegetation The Lane Shark is designed to cut all types of grass and light vegetation around ponds, road sides, and ditches. To cut grass or light vegetation place the Lane Shark approximately 1-2 inches above the ground and slowly drive forward while keeping attention to the cutting path to make sure no foreign objects are obstructing the path of the Lane Shark.
-
Page 28: Safety Requirements
OPERATING INSTRUCTIONS Lane Shark LS-3 Safety Requirements It is the operators main responsibility to ensure that the Lane Shark is being operated as safe as possible at all times. Before attempting to operate the Lane Shark, make sure you have read the owners manual. READ, UNDERSTAND, and FOLLOW all safety directions associated with the Lane Shark. -
Page 29: Transition Process
ADJUSTMENTS Lane Shark LS-3 Transition Process Your Lane Shark is capable of cutting in 11 di erent positions. Once you have successfully connected the Lane Shark to your tractor and familiarized yourself with all of its components, it is time to begin learning the transition process. -
Page 30: Directly In Front
ADJUSTMENTS Lane Shark LS-3 Directly in Front (Home) Position The directly in front or “home” position is the position that your Lane Shark is delivered in. (Refer to Figure 1 for visual reference) The Lane Shark should ALWAYS be placed in the home position when transporting, storing or mounting/dismounting from the tractor. -
Page 31: O Set
ADJUSTMENTS Lane Shark LS-3 O set Position This position allows the Lane Shark to extend from directly in front of the tractor to horizontally beside the tractor. The o set position is the recommended position for cutting around ponds, near ditches, and along roadsides. On this page you will be shown how to correctly move the Lane Shark from the home position (Shown on pg. - Page 32 ADJUSTMENTS Lane Shark LS-3 Returning Back to Home Position (From O set) When you are nished cutting with the Lane Shark in any of its positions, it is very important that you return it back to the home position. The Lane Shark is not designed to be transported or stored in any other position except the home position.
-
Page 33: Vertical
ADJUSTMENTS Lane Shark LS-3 Vertical Position This position allows the Lane Shark to extend from directly in front of the tractor to horizontally beside the tractor. The o set position is the recommended position for cutting around ponds, near ditches, and along roadsides. On this page you will be shown how to correctly move the Lane Shark from the home position (Shown on pg. - Page 34 ADJUSTMENTS Lane Shark LS-3 Returning Back to Home Position (From Vertical) When you are nished cutting with the Lane Shark in any of its positions, it is very important that you return it back to the home position. The Lane Shark is not designed to be transported or stored in any other position except the home position.
-
Page 35: Lubrication
LUBRICATION Lane Shark LS-3 Main Pivot Point The main pivot point is where the main pivot arm attaches the deck of the Lane Shark to the mounting plate. This point allows all movement of the Lane Shark and must be properly maintained. To maintain the main pivot point it must always be properly greased before use. -
Page 36: Maintenance
MAINTENANCE Lane Shark LS-3 General Routine maintenance is key to the longevity of any implement. It is very important that you maintain your Lane Shark as described below. It also is recommended that you change your tractors hydraulic uid per your tractors manufactures recommendation to ensure the longevity of your Lane Shark and tractor. -
Page 37: Proper Storage
STORAGE Lane Shark LS-3 Overview To keep your Lane Shark in its best condition, we recommend following the storage procedures listed below. It will also make sure your Lane Shark is o to a good start when needed. If your Lane... -
Page 38: Limited Warranty
LIMITED WARRANTY Lane Shark LS-3 Warranty Information When purchasing from Lane Shark USA, we guarantee that we deliver exactly what is seen and described in our advertisement. Except for the excluded products as described below, Lane Shark USA warrants the original purchaser that... -
Page 39: Reference Material
REFERENCE MATERIAL Lane Shark LS-3 GLOSSARY OF TERMS TERM DEFINITION Ballast Weight added to the tractor to increase stability such as weight plates added to the front of the tractor, wheel weights, or adding uid to the tires. Blade Carrier The metal bar connected to the main shaft to which both cutting blades are bolted. -
Page 40: Parts Breakdown
REFERENCE MATERIAL Lane Shark LS-3 PARTS BREAKDOWN DESCRIPTION QTY PER UNIT TOOLS NEEDED PART NO. BLADE MATERIAL 15”x3” Rotary Blades BKLS3000002022A 2-1/16”x1-1/8” Cutter BBLSS000002022A Bolt 1-1/8” Lock Washer BBLSS000002022A 1-1/2” End 1-1/8” Rotary Cutter BBLSS000002022A Wrench PIN MATERIAL Red Handle Pins... - Page 41 REFERENCE MATERIAL Lane Shark LS-3 DESCRIPTION QTY PER UNIT TOOLS NEEDED PART NO. MOTORS 5.5 GPM Danfoss MRLS3D00002022A gear motor 1/2” - 14x1.5” Motor 3/8” Allen Wrench Mount Bolts 1/2” Split Lock Washer ROTATING ASSEMBLY MATERIAL Spindle Housing SHLSS000002022B Main Shaft...
-
Page 42: Frequently Asked Questions
REFERENCE MATERIAL Lane Shark LS-3 FREQUENTLY ASKED QUESTIONS Where can I nd my serial number? Your Lane Shark will come with three serial number stickers. Your serial number should read “LS2-XXXX”. The serial number stickers can be found in the following locations: 1) On the front face of the backplate in the upper right corner;... - Page 43 REFERENCE MATERIAL Lane Shark LS-3 NOTES (850) 610-2870 www.lanesharkusa.com...