1. Manuals
  2. Brands
  3. JETWAY Manuals
  4. PCI Card
  5. 845GVFD
  6. User manual

JETWAY 845GVFD User Manual

M/b for socket 478 pentium 4 processor
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
845GVFD
USER'S MANUAL
M/B For Socket 478 Pentium 4 Processor
NO. G03-845GVFD
Rev:1.0
Release date: February 2004
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 845GVFD and is the answer not in the manual?

Questions and answers

Summary of Contents for JETWAY 845GVFD

  • Page 1 845GVFD USER'S MANUAL M/B For Socket 478 Pentium 4 Processor NO. G03-845GVFD Rev:1.0 Release date: February 2004 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

  • Page 2: Table Of Contents

    TABLE OF CONTENT USER’S NOTICE........................ii MANUAL REVISION INFORMATION ................ii COOLING SOLUTIONS ......................ii CHAPTER 1 INTRODUCTION OF 845GVFD MOTHERBOARD FEATURE OF MOTHERBOARD ..................1 SPECIFICATION........................2 PERFORMANCE LIST ......................3 LAYOUT DIAGRAM & JUMPER SETTING ..............4 CHAPTER 2 HARDWARE INSTALLATION HARDWARE INSTALLATION STEPS ................

  • Page 3: User's Notice

    TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE 845GVFD MOTHER-BOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE.

  • Page 4: Chapter 1 Introduction Of 845Gvfd Motherboard

    845GVFD Motherboard 1-1 Feature of motherboard The 845GVFD motherboard is design for use Intel Pentium 4 Processor in 478 Pin Package/Northwood Processor with the Intel 845GV Chipset delivers a high performance and professional desktop platform solution. Which utilize the Socket 478 design (Support Hyper Threading CPU) and the memory size expandable to 2.0GB.

  • Page 5: Specification

    Description ∗ ATX form factor 6 layers PCB size: 17.6x24.4cm Design ∗ Intel 845GV Graphics Memory Controller Hub for 845GVFD Chipset ∗ Intel 82801DB I/O Controller Hub (ICH4) Chipset ∗ Support Intel Pentium 4 478 Pin package utilizes Flip-Chip Pin...

  • Page 6: Layout Diagram & Jumper Setting

    The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.) Performance Test Report CPU:...
  • Page 7 6-Channel Speaker PRINT Center/Base PS/2 Mouse REAR Speaker PS/2 Keyboard Front Speaker SPDIF-OUT ATX 12V Power Conn. K/B Power ON Jumper ATX Power Conn. (JP1) PS2 KB/Mouse Port DIMM Socket X2 USB Port/LAN Connector CPU FAN CPU Socket Intel 82845GV Chip PC99 Back Panel Serial Port COM2 USB Port...
  • Page 8 Keyboard Power On Enable/Disabled 3-pin Block CPU Frequency Select 3-pin Block CMOS RAM Clear 3-pin Block Connectors Connector Name Description Page ATXPWR ATX Power Connector 20-pin Block P.11 ATX12V ATX 12V Power Connector 4-pin Block P.11 KB/MOUSE PS/2 Mouse & PS/2 Keyboard 6-pin Female P.11 (PS2 KB/MOUSE)

  • Page 9: Chapter 2 Hardware Installation

    Hardware installation 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard jumper setting 2. Install CPU and Fan 3. Install System Memory (DIMM) 4. Install Expansion cards 5. Connect IDE and Floppy cables, Front Panel /Back Panel cable 6.

  • Page 10: Glossary

    A battery must be used to retain the motherboard configuration in CMOS RAM short 1-2 pins of JP3 to store the CMOS data. To clear the CMOS, follow the procedure below: Turn off the system and unplug the AC power Remove ATX power cable from ATX power connector Locate JP3 and short pins 2-3 for a few seconds Return JP3 to its normal setting by shorting pins 1-2...

  • Page 11: About Intel Pentium 4 478-Pin Cpu

    establish the relationship between the various components. Driver - software, which defines the characteristics of a device for use by another device or other software. Processor - the "central processing unit" (CPU); the principal integrated circuit used for doing the "computing" in "personal computer" Front Side Bus Frequency - the working frequency of the motherboard, which is generated by the clock generator for CPU, DRAM and PCI BUS.

  • Page 12: Expansion Card

    This motherboard provides 184-pin DUAL INLINE MEMORY MODULES (DIMM) sites for memory expansion available from minimum memory size of 64MB to maximum memory size of 2.0GB DDR SDRAM. Valid Memory Configurations Bank 184-Pin DIMM Total Memory Bank 0, 1 (DDR1) DDR200/DDR266 64MB∼1.0GB DDR SDRAM Module...

  • Page 13: Assigning Irq For Expansion Card

    3. Align the card’s connectors and press firmly. 4. Secure the card on the slot with the screen you remove above. 5. Replace the computer system’s cover. 6. Set up the BIOS if necessary. 7. Install the necessary software driver for your expansion card. 2-5-2 Assigning IRQs For Expansion Card Some expansion cards need an IRQ to operate.
  • Page 14 ATX Power Supply connector. This is a new defined 20-pins connector that usually comes with ATX case. The ATX Power Supply allows to use soft power on momentary switch that connect from the front panel switch to 2-pins Power On jumper pole on the motherboard. When the power switch on the back of the ATX power supply turned on, the full power will not come into the system board until the front panel switch is momentarily pressed.
  • Page 15 COM_2 is the 9-pin D-Subminiature mail connector. The On-board serial port can be disabled through BIOS SETUP. Please refer to Chapter 3 “INTEGRATED PERIPHERALS SETUP” section for more detail information. (10) SPDIF-Out Optical Connector : OPT Optical Transmitter Connector for SPDIF Speaker or SPDIF device. PS/2 6-Channel Speaker PRINT...

  • Page 16: Headers

    disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector. IDE2 Pin 1 Secondary IDE Connector • Two hard disks can be connected to each connector. The first HDD is referred to as the “Master”...
  • Page 17 These headers are used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel. USB2 USB1 OC (Over Current) +DATA +DATA +DATA +DATA DATA DATA DATA...
  • Page 18 This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting in order to prolong the lift of the system’s power supply. See the figure below.
  • Page 19 (12) IR infrared module Headers (5-pin) : IR This connector supports the optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function. Pin 1 IR infrared module Headers (13) CD Audio-In Headers (4-pin) : CDIN CDIN are the connectors for CD-Audio Input signal.

  • Page 20: Starting Up Your Computer

    2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used.

  • Page 21: Chapter 3 Introducing Bios

    Chapter 3 Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization.

  • Page 22: The Main Menu

    3-3 The Main Menu Once you enter Award  BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.

  • Page 23: Standard Cmos Features

    Load Optimized Defaults Use this menu to load the BIOS default values that are settings for optimal performances system operations. Load Standard Defaults Use this menu to load the BIOS default values that are factory settings for the stable performance system operation. Set Supervisor/User Password Use this menu to set User and Supervisor Passwords.

  • Page 24: Advanced Bios Features

    Time The time format is <hour><minute><second>. Primary Master/Primary Slave Secondary Master/Secondary Slave Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category.
  • Page 25 Anti-Virus Protection Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table.

  • Page 26: Advanced Chipset Features

    Typematic Rate Setting Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected. The settings are: Enabled/Disabled. Typematic Rate (Chars/Sec) Sets the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, and 30.

  • Page 27: Dram Timing Settings

    Video RAM Cacheable Select Enabled allows caching of the video BIOS, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The settings are: Enabled and Disabled. Memory Hole At 15M-16M You can reserve this area of system memory for ISA adapter ROM.

  • Page 28: Integrated Peripherals

    CMOS Setup Utility – Copyright(C) 1984-2004 Award Software Integrated Peripherals > Onboard IDE Function Press Enter Item Help > Onboard Device Function Press Enter > Onboard Super IO Function Press Enter USB2.0 Controller Enabled Menu Level > Init Display First PCI Slot Power On Function Button Only...

  • Page 29: Onboard Device Function

    The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately. The settings are: Enabled and Disabled. Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports.

  • Page 30: Power Management Setup

    CMOS Setup Utility – Copyright(C) 1984-2004 Award Software Onboard Super IO Function Onboard FDD Controller Enabled Item Help Onboard Serial Port 1 3F8/IRQ4 Onboard Serial Port 2 2F8/IRQ3 UART2 Mode Select Normal Menu Level >> RxD, TxD Active Hi, Lo IR Transmission Delay Enabled IR Duplex Mode...
  • Page 31 The Power Management Setup allows you to configure your system to most effectively save energy saving while operating in a manner consistent with your own style of computer use. CMOS Setup Utility – Copyright(C) 1984-2004 Award Software Power Management Setup ACPI Function Enabled Item Help...

  • Page 32: Pm Timer Reload Events

    use this function. During Enabled, choose the Date and Time Alarm: Date(of month) Alarm You can choose which month the system will boot up. Set to 0, to boot every day. Time(hh:mm:ss) Alarm You can choose what hour, minute and second the system will boot up. Note: If you have change the setting, you must let the system boot up until it goes to the operating system, before this function will work...

  • Page 33: Irq Resources

    Data (ESCD) when you exit Setup if you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the operating system can not boot. The settings are: Enabled and Disabled. Resource Controlled By The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and Plug and Play compatible devices.

  • Page 34: Miscellaneous Control

    only available if there is Hardware Monitor onboard. CMOS Setup Utility – Copyright(C) 1984-2004 Award Software PC Health Status Shutdown Temperature Disabled Item Help CPU Warning Temperature Disabled Show PC Health in Post Enabled 25 ° C Current System Temperature 38 °...

  • Page 35: Load Standard/Optimized Defaults

    CMOS Setup Utility – Copyright(C) 1984-2004 Award Software Miscellaneous Control CPU Clock Ratio Item Help Auto Detect PCI Clk Enabled Spread Spectrum Disabled ** Current Host Clock is 100/33MHz ** Menu Level > HOST/PCI Clock at Next Boot is 100/33MHz ** Current DRAM Clock is 133MHz ** DRAM Clock at Next Boot is 133MHz...

  • Page 36: Set Supervisor/User Password

    Load Standard Defaults (Y/N)? N Pressing <Y> loads the BIOS default values for the most stable, minimal-performance system operations. Load Optimized Defaults When you press <Enter> on this item, you get a confirmation dialog box with a message similar to: Load Optimized Defaults (Y/N)? N Pressing <Y>...

  • Page 37: Magic Install Supports Windows 98Se/Me/Nt4.0/2000/Xp

    DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. We call this auto detect software MAGIC INSTALL.

  • Page 38: Vga Install Intel 845G Vga Driver

    1. Click INF in the MAGIC INSTALL MENU 2. Click NEXT when Chipset Software Install Utility appears 3. This chart shows motherboards supported by 4. Select if you want computer re-started click the driver click Yes Finish NOTE: MAGIC INSTALL will auto detect file path X:\INTEL845\INF\SETUP.EXE This driver supports WINDOWS 98SE/ME/2000/XP (NT4.0 do not require) 4-2 VGA...

  • Page 39: Sound Install Alc Audio Codec Driver

    1. Click VGA when MAGIC INSTALL MENU Click NEXT When Intel (R) Brookdale-G- appears 830M Chipset Graphics Driver Software Setup Click YES, This is Announce CopyRight 4. If You Want Re-start Computer , Click FINISH 4-3 SOUND Install ALC Audio Codec Driver 1.

  • Page 40: Lan Install Rtl810X Lan Controller Driver

    3. Click Finish and Restart Windows 4. Click Start→Program→Avance Sound Manager→AvRack. Then AVRACK Windows appears 5. Sound Effect select and KaraOK Mode 6. Manual Sound Effect Setting Function Note: The path of the file For WIN98/NT4.0/WIN2K/XP is X:\CODEC\ALC\SETUP.EXE 4-4 LAN Install RTL810X LAN Controller Driver The path of the file: for WINDOWS 98SE is X:\RTLLAN\WIN98 for WINDOWS 98ME is X:\RTLLAN\WINME...

  • Page 41: Pc-Health Winbond 83627Thf Hardware Doctor

    3. Window can find Realtek RTL8139/810X 4. Click FINISH and restart your computer family fast Ethernet NIC, when OS ask CAT file path, change the directory to X:\RTLLAN\WIN98 (If OS is win9X) 4-5 PC-HEALTH Winbond 83627THF Hardware Doctor The path of the file is X:\INTEL\83627thf\SETUP.EXE 1.

  • Page 42: How To Utilize Pc-Health

    4-5-1 How To Utilize PC-HEALTH 1. After executing Winbond Hardware Doctor it 2. This is a CPU/System Fan Speed and supports system voltage, Fan speed and Temperature status information CPU/SYSTEM Temperature. Because this is a On-time Monitoring program therefore the value will change after it detected, if the value is over default setting the system will have warning picture and beeps.
  • Page 43 5. When On-line update BIOS the program will 6. Click Next if you need update BIOS, after auto-check your BIOS version upgrade BIOS, the system will clear CMOS and automatically restart Click Yes if you want to update the BIOS When System programming BIOS don’t turn otherwise choose No to exit off power, after finish update BIOS, the...

  • Page 44: Iaa Install Intel Application Accelerator Software

    4-7 IAA Install Application Accelerator Software The Intel Application Accelerator is designed to improve performance of the storage sub-system and overall system performance. This software delivers improved performance through several ingredient technologies (components). Certain components will be available only on Pentium ...

  • Page 45: How To Install Usb 2.0 Driver

    5. Click INSTALL, Start to install the software 6. Setup Complete and click FINISH 7. After PC-CILLIN 2004 complete, Please register your information and we recommend select update item to download newest engine code and virus code Note : Please install ACROBAT READER, Before you read PC-CILLIN 2004 User Manual, the path at X:\acrobat\adberdr6_enu_full.exe 4-9 HOW TO INSTALL USB 2.0 DRIVER Windows 98SE/ME USB 2.0 Driver installation...

  • Page 46: How To Disable On-Board Sound

    You may copy from DRIVER CD X:\FLASH\AWDFLASH.EXE or download from our web site. STEP 3. Copy latest BIOS for 845GVFD from our web site to your boot disc. STEP 4. Insert your boot disc into A:, start the computer, type “Awdflash A:\845GVFDAxxx.BIN /SN/PY/CC/R”...

Table of Contents