Sealey SA29/S.V3 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction Wear eye
manual protection
1. SAFETY
 Follow all workshop safety rules, regulations, and conditions when using wrench.
 WARNING! Disconnect from air supply before changing accessories or servicing.
 Maintain the wrench in good condition and replace any damaged or worn parts. Use g e n u i n e parts only. Unauthorised parts may
be dangerous and will invalidate the warranty.
 WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
 Only use impact sockets which are specifically designed for use with an impact wrench.
 Wear approved safety eye/face shield, ear defenders, and hand protection.
 WARNING! Due to the possible presence of asbestos dust from brake linings, when working around vehicle brake systems we recommend you
wear suitable respiratory protection.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
 Keep children and non essential persons away from the working area.
 DO NOT use the wrench for a task it is not designed to perform.
 WARNING! DO NOT use wrench if damaged or thought to be faulty. (Contact Service Agent).
 DO NOT use wrench unless you have been instructed in its use by a qualified person.
 DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
 DO NOT operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
 DO NOT carry wrench with your hand on the trigger in order to avoid unintentional starting.
 DO NOT direct air from the air hose at yourself or others.
 When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. INTRODUCTION
Suitable for commercial and agricultural vehicle use. Long anvil and straight configuration with rocking-dog hammer for applications with restricted
access. Fitted with reverse action. Supplied with side handle.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA29/S
Drive: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1"Sq
Working Torque:. . . . . . . . . . . . . . . . . . . . . . . . . . .1170lb.ft(1591Nm)
Maximum Torque: . . . . . . . . . . . . . . . . . . . . . . . . .1460lb.ft(1986Nm)
Ultimate Torque:. . . . . . . . . . . . . . . . . . . . . . . . . . .1520lb.ft(2067Nm)
Free Speed:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4000rpm
Air Consumption: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15cfm
Operating Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90psi
Inlet Size:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2"BSP
Weight:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5kg
Noise Power/Pressure: . . . . . . . . . . . . . . . . . . . . 106.71/95.71dB(A)
Vibration/Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . 9.94/0.90m/s²
4. PREPARATION
4.1. Air Supply
Recommended hook-up procedure is shown in fig 1.4.1.1. Ensure wrench air valve (or trigger) is in the "off" position before
connecting to the air supply.
4.1.2. You will require an air pressure of 90psi, and an air flow according to specification.
4.1.3.  WARNING: Ensure the air supply is clean and does not exceed 90 psi while operating the wrench. Too high an air pressure and
unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.4. Drain the air tank daily. Water in the air line will damage the wrench.
4.1.5. Clean air inlet filter weekly.
4.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be
1/4" I.D. and fittings must have the same inside dimensions.
4.1.7. Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
© Jack Sealey Limited
INSTRUCTIONS FOR:
1" SQUARE DRIVE AIR IMPACT WRENCH
SA29/S.V3
MODEL NO:
Wear ear Wear a mask Wear protective
protection
Original Language Version
gloves
SA29/S.V3 Issue: 5 - 01/08/17