Summary of Contents for Crestron Electronics FT2A-PWR-JP-1-BASIC
- Page 1 FT2A-PWR-JP-1-BASIC FlipTop™ AC Power Outlet Module, Single, JP NEMA® 5, Type B Product Manual Crestron Electronics, Inc.
- Page 2 Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource. Crestron, the Crestron logo, and FlipTop are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. NEMA is either a trademark or registered trademark of the National Electrical Manufacturers Association in the United States and/or other countries.Other trademarks, registered trademarks, and...
-
Page 3: Table Of Contents
Contents Overview Specifications Product Specifications Dimension Drawings FT2A-PWR-JP-1-BASIC Installation In the Box Install the Module Operate the Module Above the Table Product Manual — Doc. 9401A Contents • iii... - Page 4 iv • Contents Product Manual — Doc. 9401A...
-
Page 5: Overview
AC power outlet module to an AC power source. The FT2A-PWR-JP-1-BASIC AC power outlet module is rated for 10A at 125VAC, 50/60 Hz. The module is suitable for use in Japan and other countries where Type B power outlets are used. The FT2A-PWR-JP-1-BASIC occupies two consecutive module slots within the FlipTop assembly. -
Page 6: Specifications
Specifications Product specifications for the FT2A-PWR-JP-1-BASIC. Product Specifications Power Rating 10A at 125VAC, 50/60 Hz Receptacles and Plugs Outlet Above Table (1) NEMA 5-15R grounded AC power receptacle, Commerce Dept. Type B Outlet Below Table None Main Power Plug (1) 2.44 m (8 ft) attached cable with NEMA 5-15P grounded AC power plug... -
Page 7: Dimension Drawings
Dimension Drawings Product Manual — Doc. 9401A FT2A-PWR-JP-1-BASIC • 7... -
Page 8: Ft2A-Pwr-Jp-1-Basic Installation
FT2A-PWR-JP-1-BASIC Installation The FT2A-PWR-JP-1-BASIC is designed for installation in Crestron FT2 FlipTop™ assemblies. The power outlet module provides one NEMA AC power outlet on top of the table. An 2.44 m (8 ft) three-prong power cord is fixed to the bottom of the module. The power outlet module is PSE listed and rated for 10A (total) at 125V, 50/60 Hz. -
Page 9: Install The Module
4. Lift and remove any module being replaced by a power outlet module. 5. Insert the power cable of the power outlet module through the empty module slots. Product Manual — Doc. 9401A FT2A-PWR-JP-1-BASIC • 9... - Page 10 9. Using a manual torque screwdriver set to its lowest possible setting, hand tighten the locking bar screws until the locking bars are secured to the FT2 FlipTop assembly. 10 • FT2A-PWR-JP-1-BASIC Product Manual — Doc. 9401A...
-
Page 11: Operate The Module Above The Table
1. Tap the lid retraction button to retract the one-touch lid, which disappears into the FT2 FlipTop assembly. 2. Plug a device into the outlet on the power outlet module. 3. Confirm that the power indicator on the device shows that the device is receiving power. Product Manual — Doc. 9401A FT2A-PWR-JP-1-BASIC • 11... - Page 12 Crestron Electronics, Inc. Product Manual — Doc. 9401A 15 Volvo Drive, Rockleigh, NJ 07647 06/16/23 Tel: 888.CRESTRON Specifications subject to Fax: 201.767.7656 change without notice. www.crestron.com...
Need help?
Do you have a question about the FT2A-PWR-JP-1-BASIC and is the answer not in the manual?
Questions and answers