Related Manuals for Samsung DVE50T7450 Series
Summary of Contents for Samsung DVE50T7450 Series
- Page 1 Dryer User manual DVE50T7450* DC68-03784K-03_IB_DV7450M_EN.indd 1 DC68-03784K-03_IB_DV7450M_EN.indd 1 2023-06-29 2023-06-29 10:53:43 10:53:43...
-
Page 2: Table Of Contents
Contents Safety information What you need to know about the safety instructions Important safety symbols CALIFORNIA PROPOSITION 65 WARNING Important safety precautions Warnings Cautions Installation requirements Key installation requirements Location considerations Ducting requirements Exhausting requirements Gas requirements Electrical requirements Installation What’s included Step-by-step installation Vent blockage test... - Page 3 Maintenance Cleaning Troubleshooting Checkpoints Information codes Specifications Fabric care chart Protecting the environment Specification sheet English 3 DC68-03784K-03_IB_DV7450M_EN.indd 3 DC68-03784K-03_IB_DV7450M_EN.indd 3 2023-06-29 2023-06-29 10:53:52 10:53:52...
-
Page 4: Safety Information
Safety information Congratulations on your new Samsung dryer. This manual contains important information on the installation, use and care of your appliance. Please take some time to read this manual to take full advantage of your dryer’s many benefits and features. - Page 5 Read all instructions before using the appliance. As with any equipment that uses electricity and moving parts, potential hazards exist. To safely operate this appliance, familiarize yourself with its operation and exercise care when using it. WARNING - Risk of Fire •...
- Page 6 Safety information WARNING - To reduce the risk of fire or explosion: • Do not dry items that have been previously cleaned, washed, soaked, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances. They emit vapors that could ignite or explode. Any material that has been in contact with a cleaning solvent or flammable liquids or solids should not be placed in the dryer until all traces of these...
- Page 7 WARNING - Fire or explosion hazard • Failure to follow safety warnings exactly could result in serious injury, death or property damage. • Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance.
- Page 8 Safety information WARNING - What to do if you smell gas: • Do not try to light any appliance. • Do not turn on the appliance. • Do not touch any electrical switch. • Do not use any phone in your building. •...
-
Page 9: California Proposition 65 Warning
CALIFORNIA PROPOSITION 65 WARNING WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov. Important safety precautions WARNING To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: Read all instructions before using this appliance. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode. - Page 10 Safety information 13. Do not use heat to dry articles containing foam rubber or similarly textured rubber- like materials. 14. Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt. 15. The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel.
-
Page 11: Warnings
Warnings WARNING • Ensure pockets are free of small, irregularly shaped hard objects and foreign material, i.e. coins, knives, pins, etc. These objects could damage your dryer. • Gas leaks may occur in your system, resulting in a dangerous situation. Cautions CAUTION •... - Page 12 Safety information • Do not place items in your dryer that have been spotted or soaked with vegetable oil or cooking oil. Even after being washed, these items may contain significant amounts of these oils. • Residual oil on clothing can ignite spontaneoulsy. The potential for spontaneous combustion increases when items containing vegetable oil or cooking oil are exposed to heat.
-
Page 13: Installation Requirements
Installation requirements Read through the following instructions before installing the dryer, and keep this manual for future reference. WARNING Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel - Do not contact the following parts while the appliance is energized: Control board and inlet valve. - Page 14 Installation requirements Dimensions Type Front loading dryer A. Overall height 45.0 (1144) B. Width 27.0 (686) Dimensions (in. (mm)) C. Depth with door open 49.8 (1265) D. Depth 30.0 (763) English DC68-03784K-03_IB_DV7450M_EN.indd 14 DC68-03784K-03_IB_DV7450M_EN.indd 14 2023-06-29 2023-06-29 10:53:53 10:53:53...
- Page 15 Clearance requirement This clearance requirement is applicable for dryers only. NOTE • For washer’s clearance requirement, see the washer’s user manual. • If the washer and dryer have different clearance requirements, use the one with the larger value. Alcove or closet installations WARNING •...
- Page 16 Installation requirements This clearance requirement is applicable for washer and dryer pair installation. Side by side installation 1 in. (25 mm) 21 in. (533 mm) 1 in. (25 mm) 5.9 in. (150 mm) English DC68-03784K-03_IB_DV7450M_EN.indd 16 DC68-03784K-03_IB_DV7450M_EN.indd 16 2023-06-29 2023-06-29 10:53:53 10:53:53...
-
Page 17: Ducting Requirements
Ducting requirements Recommended Use only for short-run installation Weather hood type 4” (10.2 cm) 2.5” (6.4 cm) No. of 90° Rigid Rigid elbows 80 ft. (24.4 m) 74 ft. (22.6 m) 68 ft. (20.7 m) 62 ft. (18.9 m) 57 ft. (17.4 m) 51 ft. -
Page 18: Exhausting Requirements
Installation requirements Exhausting requirements Outside the United States and Canada The dryer must not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl • Refer to the local codes. space, or a concealed space of a building. WARNING Exhausting the dryer to the outside will •... -
Page 19: Gas Requirements
Gas requirements WARNING • Your dryer must be disconnected from the gas supply pipe system during any pressure • Use only natural or LP (liquid propane) testing of the system at pressures greater gases. than 1/2 psi (3.5 kPa). • The installation must be conformed with •... -
Page 20: Electrical Requirements
Installation requirements Electrical requirements Grounding The wiring diagram is located on the plate under the control panel or rear frame. This dryer must be grounded. In the event of malfunction or breakdown, the ground WARNING will reduce the risk of electrical shock by •... - Page 21 Electric models Electrical connections Before operating or testing, follow all WARNING grounding instructions in the “Grounding” • Your dryer has an optional cord with section. An individual branch (or separate) an equipment-grounding conductor circuit serving only your dryer is and a grounding plug. This cord is sold recommended.
- Page 22 Installation requirements Electric models – Canada Only WARNING A 120 / 240 volt, 60 Hz AC approved Risk of Electric Shock electrical service fused through a When local codes allow, you can connect 30-ampere fuse or circuit breaker on both the dryer’s electrical supply with a new sides of the line is required.
-
Page 23: Installation
What’s included Make sure all the parts are included in the product package. If you have a problem with the dryer or the accessories, contact a local Samsung customer center or the retailer. Dryer at a glance 01 Control panel... - Page 24 Installation Accessories & tools Provided accessories Y connector Water hose Short water hose (Canadian elec. models only) Required tools Pliers Cutting knife Pipe wrench (gas Nut driver models only) Level Philips screwdriver Duct tape Wrench LPG-safe compound or Teflon Tape (for gas installation) WARNING Packing materials can be dangerous to children.
-
Page 25: Step-By-Step Installation
Step-by-step installation Make sure you have a qualified technician install the dryer. Step by step installation instructions start below. • Do not remove the protective film on the door before completing the product installation. If you remove the protective film before the installation is complete, the door may get scratched or damaged during installation. - Page 26 Installation STEP 3 Connect the electrical wiring First, read through the “Electrical requirements” section, and follow these steps. 3-wire system 1. Loosen or remove the screws from the center terminal block. 2. Connect the neutral wire (white or center wire) of the power cable to the center, silver-colored terminal screw of the terminal block.
- Page 27 4-wire system 1. Remove the external ground connector’s screw, and connect the ground wire (green or unwrapped) of the power cable to the screw. CAUTION • To connect the ground wire to the neutral position without through contact A (cabinet ground), contact a technician.
- Page 28 Installation • Remove the terminal block cover plate. Insert the power cord with a UL-listed strain relief through the hole provided in the cabinet near the terminal block. • A strain relief must be used. Do not loosen the nuts already installed on the terminal block.
- Page 29 Using the short hose as an extension 1. Close the cold water tap. If you have a washer cold water hose attached to the cold water faucet, unscrew and remove the hose. Then, connect the short hose (B) to the cold water tap. Turn the coupling manually until it is tight.
- Page 30 Installation STEP 5 Level the dryer To ensure optimal performance, the dryer must be level. 1. Using a level (A), check if the dryer is level side to side and then front to back. If the dryer is not level, adjust the leveling feet (B) at the bottom of the dryer.
-
Page 31: Vent Blockage Test
STEP 6 Power on (Gas models) Make sure all gas connections, the exhaust line, and all wiring is connected correctly. Then, plug the power cord into a power source and check the dryer’s installation and operation using the final checklist in Step 7 below. STEP 7 Final check When installation is complete, confirm that: •... - Page 32 Installation 2. Press the POWER button to turn the dryer on, then simultaneously press and hold the Adjust Time and Dryness buttons for 3 seconds. “InS or In” appears in the dryer’s display. (If you have started other procedures before the Vent Blockage Test, the dryer will not enter the Vent Blockage Test mode.) 3.
- Page 33 Installation check codes Check code Meaning Solution Vent condition is good. Clg (Cg) The vent is clogged. 1. Clean the lint filter. About 80 % of the vent is clogged. 2. Check your vent condition. C80 (C8) (This may decrease the drying (Refer to the “Ducting performance.) requirements”...
-
Page 34: Exhaust Ducting Guide
Installation Exhaust ducting guide Ducting 1. Make sure the dryer is installed properly so the air exhausts freely. 2. Use 4-inch rigid metal ducts. Tape all joints including the dryer connection. Never use lint-trapping screws. 3. To facilitate the exhaust, keep the ducts as straight as possible. Cleaning Clean all old ducts before installing the dryer, and make sure the vent flap opens and closes freely. - Page 35 4. Remove the two screws from the lever holder, and then remove the holder cover. 5. Put the lever holder on the other side as shown, and then tighten the screws. Install the holder cover on the opposite side as shown. 6.
- Page 36 Installation 8. Remove the glass holder, and switch the positions of: a. the hinge cover and the door handle. b. the hinge holder and the glass-guide holder 9. Remove the door lever, and then move it to the other side as shown. 10.
-
Page 37: Before You Start
Before you start Here are a few things you should know before starting your dryer. Sort and load • Put one wash load in the dryer at a • Overloading reduces the tumbling time. performance, resulting in uneven • Do not mix heavy and lightweight items drying and wrinkling. -
Page 38: Operations
Operations WARNING To reduce the risk of fire, electric shock, or injury to persons, read the “Safety information“ before operating this appliance. Feature panel Turn the cycle selector to select a desired cycle. When a cycle is selected, the cycle indicator lights up. 01 Cycle Selector •... - Page 39 Temperature can only be adjusted in TIME DRY cycle. Press to change the temperature of the current cycle. You can select from 4 different options. Please select the appropriate temperature depending on the items in the load. • High: For sturdy cottons or those labeled Tumble Dry. 03 Temp.
-
Page 40: Simple Steps To Start
Operations Icon description This icon displays after every load as a reminder to clean the lint filter. Clean the lint filter before every cycle and Filter Check make sure the filter is properly inserted before starting a cycle. This icon appears when the dryer is in steam process. The Steam dryer sprays water into the drum to deodorize clothes and reduce static electricity and wrinkles. -
Page 41: Cycle Overview
Cycle overview Sensor Dry Sensor Dry cycles sense moisture in the load and stop the dryer when the load reaches the dryness level you have selected with Dryness. Cycle Description For most fabrics including cottons and linens. NORMAL If NORMAL is selected, the Eco Dry function is enabled by default. For more information, see Eco Dry in the “Feature panel“... - Page 42 Operations Manual Dry You can change the drying settings manually to your preference. Cycle Description You can specify a cycle time in minutes. If TIME DRY is selected, the Eco Dry function is enabled by TIME DRY default. For more information, see Eco Dry in the “Feature panel“ section.
-
Page 43: Cycle Chart
Cycle chart NOTE For best results, follow the load size recommendations for each dry cycle. • Large load: Fill the drum to about full. Do not add items over this level as they need to tumble freely. • Medium load : Fill the drum to about full. - Page 44 Operations NOTE • : factory setting, : can be selected Temperature setting Time Cycle setting High Medium Extra Low NORMAL HEAVY DUTY BEDDING Sensor Dry PERM PRESS DELICATES TOWELS TIME DRY Manual Dry ...
-
Page 45: Cycle Guide
Cycle guide The best way to dry items is to follow the instructions on the care label. If no drying instructions are provided, see the following table for reference. Cycle Description Follow the care label instructions or dry using BEDDING. Bedspreads &... -
Page 46: Special Features
Operations Special features Drum Light Child Lock To turn on the drum light while the Child Lock prevents children from dryer is running, press and hold Time for playing with the dryer. When Child Lock 3 seconds. is activated, all buttons except for the POWER button are disabled. - Page 47 To use Smart Care, you must have the smartphone are parallel or nearly Samsung Smart Care app installed on your parallel. smartphone. • After you use this function, the dryer...
-
Page 48: Maintenance
Maintenance Keep the dryer clean to prevent decreased performance and to lengthen its life cycle. WARNING Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel - Do not contact the following parts while the appliance is energized: Control board and inlet valve. -
Page 49: Troubleshooting
Troubleshooting Checkpoints If the dryer operates abnormally, first check the list of problems in the table below and try the suggested actions. Problem Action • Make sure the door is latched shut. • Make sure the power cord is plugged into a live electrical outlet. - Page 50 Troubleshooting Problem Action • Check all of the above, plus... • Make sure the exhaust hood outside your home can open and close freely. • Check the exhaust system for lint buildup. Ducting should be inspected and cleaned annually. • Use a 4” rigid metal exhaust duct. •...
- Page 51 Extended time. reached. The drying time can change according to the type and amount of laundry. See the cycle chart for reference. If a problem persists, contact a local Samsung service center. English 51 DC68-03784K-03_IB_DV7450M_EN.indd 51 DC68-03784K-03_IB_DV7450M_EN.indd 51 2023-06-29...
-
Page 52: Information Codes
• If this information code remains, contact a Samsung service center. Incorrect door switch. • Contact a Samsung service center. If any information code keeps appearing on the screen, contact a Samsung service center. English DC68-03784K-03_IB_DV7450M_EN.indd 52 DC68-03784K-03_IB_DV7450M_EN.indd 52 2023-06-29... -
Page 53: Specifications
Specifications Fabric care chart Bleach The following symbols provide garment care direction. The clothing care labels Any bleach (when needed) include symbols for drying, bleaching, drying and ironing, or dry cleaning when Only non-chlorine (color-safe) necessary. The use of symbols ensures bleach (when needed) consistency among garment manufacturers Tumble dry... -
Page 54: Protecting The Environment
Specifications Iron dry or steam temperatures Dry-clean High Dry-clean Medium Do not dry-clean Line dry / Hang to dry Drip dry Warning symbols for laundering Dry flat Do not wash Do not wring Do not bleach Do not tumble dry No steam (added to iron) Do not iron Protecting the environment... -
Page 55: Specification Sheet
Specification sheet Type Front loading dryer Model name DVE50T7450* Capacity (Cu.ft) Water pressure - psi (kPa) 20-116 (137-800) NET weight lb (kg) 119 (54) Heater rating Electric (W) 5300 Power consumption (W) 5400 English 55 DC68-03784K-03_IB_DV7450M_EN.indd 55 DC68-03784K-03_IB_DV7450M_EN.indd 55 2023-06-29 2023-06-29 10:53:59 10:53:59... - Page 56 If the product is located in an area where service by a SAMSUNG authorized servicer is not available, you may be responsible for a trip charge or required to bring the product to a SAMSUNG authorized service center for service.
- Page 57 Visits by an authorized servicer to explain product functions, maintenance or installation are not covered by this limited warranty. Please contact SAMSUNG at the number below for assistance with any of these issues. English 57 DC68-03784K-03_IB_DV7450M_EN.indd 57...
- Page 58 PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states do not allow exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
- Page 59 If service is not available, SAMSUNG may elect to provide transportation of the product to and from an authorized service center. SAMSUNG will repair, replace, or refund this product at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above.
- Page 60 God; use of products, equipment, systems, utilities, services, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied or authorized by SAMSUNG that damage this product or result in service problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to follow operating instructions, maintenance and environmental instructions that are covered and prescribed in the instruction book;...
- Page 61 (French) FAX : 1-866-436-4617 Visits by a Service Engineer to explain functions, maintenance or installation is not covered by warranty. Please contact your Samsung call agent for help with any of these issues. English 61 DC68-03784K-03_IB_DV7450M_EN.indd 61 DC68-03784K-03_IB_DV7450M_EN.indd 61...
- Page 62 Memo DC68-03784K-03_IB_DV7450M_EN.indd 62 DC68-03784K-03_IB_DV7450M_EN.indd 62 2023-06-29 2023-06-29 10:54:00 10:54:00...
- Page 63 Memo DC68-03784K-03_IB_DV7450M_EN.indd 63 DC68-03784K-03_IB_DV7450M_EN.indd 63 2023-06-29 2023-06-29 10:54:00 10:54:00...
- Page 64 If you change the factory default setting or enable other features, power consumption could increase and exceed the limits qualified for ENERGY STAR. QUESTIONS OR COMMENTS? COUNTRY CALL OR VISIT US ONLINE AT U.S.A 1-800-SAMSUNG (726-7864) www.samsung.com/us/support www.samsung.com/ca/support (English) CANADA 1-800-SAMSUNG(726-7864) www.samsung.com/ca_fr/support (French) DC68-03784K-03 DC68-03784K-03_IB_DV7450M_EN.indd 64 DC68-03784K-03_IB_DV7450M_EN.indd 64...