Summary of Contents for TimeTec TTS 2200B
- Page 1 . t i m e t e c c l o u d . c o m Mobile Access, TimeTec Smart Tripod Turnstile TTS 2200B Installation Manual...
- Page 2 TS2200: Tripod Turnstile TS2211: Tripod Turnstile with Controller and RFID Reader TS2222: Tripod Turnstile with Controller and Fingerprint Reader with RFID function. Please read this document carefully before installation and using the device. 1. Technical Speci cations AC 100V ~ 120V/200~240V, Center: 80 kg Input Voltage Max.
- Page 3 Rotating the arms to the connection points until it was fastening, and use the Hex key to fasten the one screw on each arm, as shown in gure 2-2. Tighten the one screw on each arm in clockwise direction. Figure 2-2 2.2 Power-on Test Before the Installation of Device 1.
- Page 4 Notes: 1. The space at the end of the arm shall not be greater than 80mm (see figure 3-1). 2. Setting a warning line for card swiping (see figure 3-2). A warning line is suggested to prompt users to swipe cards in a distance, which would greatly reduce the probability of equipment failure caused by improper operations.
- Page 5 Installation levelness Installation levelness Figure 3-5 4. Cable Diagram 4.1 Function Description of the Turnstile Control Board If you are using TS2211 or TS2222, all the connections between access control and turnstile control boards are done in factory. Just plug in communication cable to access controller and do the setting.
- Page 6 J3 Indicator (top): To connect a LED screen and indicate if user veri cation is successful and whether it is able to pass. J-NC2 Disabled Turnstile: Short circuit NC1 and GND, the turnstile is disabled, that is to say, the turnstile is locked by force. J7 Opening Signal Input: To receive relay signal and open the turnstile.
- Page 7 4.3.2 Direction Indicator It is to indicate whether the passage allows people to pass. The green arrow means passing is allowed while the red "X" means passing is prohibited. The indicator status can be set through number 4 and 5 in the DIP switch. The description of the bit settings are as follows: 11 = One-way traffic, left passing is allowed.
- Page 8 5. Equipment Precautions and Maintenance 5.1 Precaution 1. It is recommended to purchase optional accessories to use in outdoor environment. (1) It shall install optional cooling fans for the equipment if the working temperature is often above 50 ºC. (2) It is equivalent to IP54 waterproof under proper installation. However, it cannot work in the region that may su er typhoon. (3) If the temperature is -30ºC, a heating plate is suggested to install.
- Page 9 Metal Shrapnel Tri-lobed Wheel Drop-arm Solenoid Position Sensor Turnstile-opening Turnstile-opening Solenoid Solenoid Lock Rod Lock Rod Adjustable Tension Spring Figure 5-2 Figure 5-3 6. Troubleshooting Symptom Troubleshooting It may be caused by the power supply or circuit. The indicator is not lighted when the equipment is Check whether the connection cable and power cable between are damaged, or powered on.
- Page 10 Figure 6-1 Normal status (closed) of the drop-arm solenoid Normal status of the drop-arm solenoid after after being powered on being powered o Figure 6-2 Attachment 1 Default Factory Settings Function Default Lock Driving Duration Door Sensor None Veri cation Interval Controller Communication TCP/IP: 192.168.1.201 Turnstile Opening Duration...
- Page 11 Attachment 2 Connection Diagram of Mainboard and Access Control Panel Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
- Page 12 Attachedment 3 Connection of TTS 2200B main board and TimeTec BLE 2 Power Supply 12VDC...
- Page 13 © 20 18 Timetec Compu ting S dn B hd. A ll rig ht s re ser ved • 012018...
Need help?
Do you have a question about the TTS 2200B and is the answer not in the manual?
Questions and answers