GREAT PLANES ElectriFly Equinox Instructions Manual

The Equinox ™ LiPo Cell Balancer is designed to regulate the
voltages of all cells in a lithium-polymer (LiPo) pack to very tight
tolerances during charge and discharge functions. As opposed
to non-balanced packs, balanced LiPo's typically provide higher
total voltage, which means more power to the motor system. In
addition, balanced LiPo packs generally last longer as no
individual cell ever becomes over-charged, which is a big reason
why some LiPo's perform inadequately. A good balancing
system also provides a very safe charging and discharging
platform, which is critical when handling LiPo batteries.
Equinox is designed to balance LiPo packs containing
anywhere from 2 to 5 cells which are assembled in series.
Equinox will keep the voltages of all cells in the pack within
5mV (0.005V) to 30mV (0.030V) of each other at all times. It's
very important to understand that the LiPo battery MUST
be wired for balancing in order to function with Equinox!
Contact your LiPo supplier if you are unsure if your battery is
configured for balancing.
Unlike some balancers, Equinox has two separate functions:
QUICK-BALANCE MODE: By itself, Equinox can apply a small
discharge current to gently balance the voltages of all cells in a
LiPo pack. This function is called "Quick-Balance Mode."
INTERFACE MODE: Equinox can also be used as an
"interface" – connected between the LiPo pack and a separate
charger or discharger. In Interface Mode, Equinox will monitor
and control how each cell in the pack is charged or discharged
by the separate charger or discharger. Equinox is compatible
with all ElectriFly ™
PolyCharge4 ™ , etc.).
For a good overall understanding, it's strongly recommended
to read through this entire manual once before attempting to
use the Equinox Balancer.
SPECIFICATIONS
Compatible Input Devices: LiPo chargers and dischargers ONLY
Cell Balancing Range:
Max. Current (chg or dsch): 3 amps (3 – 6A requires special harness –
brand LiPo chargers
(operation based on nominal cell voltage
of 3.7V per cell)
2-series to 5-series LiPo packs
(7.4 – 18.5V)
see rear of manual)
INSTRUCTIONS
Discharge Termination:
Discharge Current:
Overload Protection:
Physical Dimensions:
Weight:
• For LiPo packs with 2 to 5 cells assembled in series
(not parallel) .
• Designed only for LiPo batteries which are wired for
balancing. NOT compatible with existing ElectriFly
brand or other brand packs which have a 2-pin charge
lead (and SafeCharge
• Balances
or discharge.
• Functioning alone it can quickly balance the voltage of all
cells in the pack (Quick-Balance Mode).
• Used in conjunction with a separate charger or discharger it
controls exactly how cells are charged or discharged so
they are balanced at all times (Interface Mode).
• Includes 2S and 3S battery adapters. Adapters available
separately for 4S and 5S packs (GPMM3162).
• Can handle 3 amps in Interface Mode (with separate
charger or discharger). Can handle currents of 3 – 6A max.
but requires optional high current adapters (GPMM3163).
• Automatically checks for poor quality cells.
• Banana plugs
charger/discharger.
• NEVER allow the input banana plugs to touch while a
battery is connected to Equinox's output, as it could cause
a short circuit and damage Equinox and the LiPo battery!
• NEVER attempt to use Equinox with batteries that are NOT
lithium-polymer.
• NEVER allow water, moisture or foreign objects into
Equinox's case.
(Triton ™ ,
• NEVER leave Equinox unattended while in use at ANY time.
• NEVER place Equinox, the charger/discharger, or battery
on a flammable surface or near a combustible material
while in use. Do not lay on a carpet, cluttered workbench,
paper, plastic, vinyl, leather, wood, inside an R/C model or
full sized automobile!
• Do not block the air intake holes, which could cause
Equinox to overheat.
• Do not attempt to use batteries with more cells or total
voltage than listed in the specifications.
• Do not attempt to charge or discharge a battery through
Equinox at a current exceeding 6 amps, as permanent
damage could result.
• IMMEDIATELY
charger/discharger and battery if Equinox or the battery
becomes hot!! Allow Equinox and battery to cool down
before reconnecting.
™
auto-cut based on individual cell voltages
2.75V per cell in Quick-Balance Mode
3.0V per cell in Interface Mode with
separate discharger
120mA per cell (Quick-Balance Mode)
7.5 amp auto (spade) fuse
3.23 x 1.57 x 0.59 oz. [82 x 40 x 15 mm]
1.55 oz. [43.8 g]
SPECIAL FEATURES
™ circuit).
individual cell voltages
on input for easy
IMPORTANT PRECAUTIONS
disconnect Equinox
™
during charge
connection to
from the