Advertisement
Quick Links
Advertisement
Related Manuals for G4M 500 Series
Summary of Contents for G4M 500 Series
- Page 1 500 SERIES MODULAR SYSTEM User Manual...
- Page 3 Warning WARNING! VAROITUS! Do not open cover. No user-serviceable parts inside. Refer servicing to qualified service personnel. Älä avaa kantta. Ei sisällä käyttäjä-huollettavia osia. Huollot saa suorittaa vain pätevä huoltomies. Do not place the product in a location near a heat source such as a radiator, or in an area subject to direct sunlight, excessive dust, Älä...
- Page 4 Warning ADVARSEL! Ikke åpne dekselet. Inneholder ingen deler som kan brukes. Overlat reperasjon til kvalifisert servicepersonell. Ikke plasser produktet i nærheten av varmekilder som f.eks. en radiator, eller i områder som er utsatt for direkte sollys, mye støv, mekanisk vibrasjon eller støt. Produktet må...
- Page 5 500 Series Thank you for purchasing a G4M 500 series product. To get the most out of your product, please read this manual carefully.
- Page 6 500-Pre 1. GAIN 500-PRE Sets the input gain, switching to the off position mutes the input. 2. MIC / LINE / DI LEDS Indicate which input is in use. 3. +48 Activates 48v phantom power. 4. IMPEDANCE GAIN Sets the Mic input impedance between 300 and 1200 ohms. LINE 5.
- Page 7 Description The G4M 500 Series Vintage Preamp is a single slot 500 series format single channel mic, line and instrument preamplifier. The transformer balanced, fully discrete signal path provides a classic warm and punchy sound with modern enhancements that make it suitable in a wide range of recording applications.
- Page 8 500-Comp 1. SIGNAL METER 500-COMP The three LEDs indicate the level of the incoming signal. BELOW – Signal is below the threshold level, ABOVE – Signal is above the threshold level, CLIP – Signal is clipping and gain must be reduced. BELOW ABOVE CLIP 2.
- Page 9 Description The G4M 500 Series Compressor is a fully variable compressor in the 500 series format. It’s compact form and discrete circuitry provide clean compression with low noise with total control over the dynamics of your incoming signal. Specifications Voltage Requirement ..±16V Input Impedance .
- Page 10 500-Eq 1. HF GAIN 500-EQ Adjust the high frequency gain from -15dB to +15dB. 2. HF FREQUENCY Select the high frequency you wish to adjust from 8KHz to 20KHz. Select OFF to disable the high frequency EQ. 3. HP FREQUENCY Applies a high pass filter to the signal between 50Hz and 300Hz.
- Page 11 Description The G4M 500 Series Equaliser is a classic push-pull equaliser in the 500 Series format. This versatile sound sculptor uses transformer based discrete circuitry to provide useful shaping for any audio source across the entire frequency spectrum. Specifications Voltage Requirement ..±16V Input Impedance .
- Page 12 SLOT 2 SLOT 3 500-RACK3 1. THREE CARD SLOT 2. POWER CONNECTORS Suitable for single width 500 series modules. Modules used a shared pool of 500mA of current through the card slot connector. SLOT 1 SLOT 2 SLOT 3 SLOT 3...
- Page 13 Description The G4M 500 Series Rack, 3 Slot is a powered rack case for 500-Series modules capable of holding three modules while being only 1U tall. This triple module design allows for a complete channel strip in one rack mountable box. Use the FEED switches on the back to instantly connect one module to the next without the need for external patching.
- Page 14 5. CARD SLOTS Automatically feed the output of one module to the input of the next without the need for Remove the panels using the allen key provided and insert your 500 Series modules. external patching using these switches. Remove two panels for a double width module.
- Page 15 48 V Rear Panel Rear Panel 500-RACK8 SLOT 8 SLOT 7 SLOT 6 SLOT 5 SLOT 4 SLOT 3 SLOT 2 SLOT 1 MADE IN CHINA 1. I NPUT 1 4. OUTPUT 2 3 pin balanced XLR input connector for microphone level. Balanced 6.35mm jack output connectors.
- Page 16 Description The G4M 500 Series Rack, 8 Slot, is an eight-channel powered rack case for 500 Series modules. This expansive eight module design allows for complete recording and processing channel strips in one rack mountable box of 3U height. Use the FEED switches on the back to instantly connect one module to the next without the need for external patching.
- Page 18 If you have any more questions about this product, please do not hesitate to contact the Gear4music Customer Service Team on: +44 (0) 330 365 4444 or info@gear4music.com KETTLESTRING LANE | YORK | YO30 4XF | UNITED KINGDOM • LAHNSTRAßE 27 | 45478 MÜLHEIM AN DER RUHR | DEUTSCHLAND • WWW.GEAR4MUSIC.COM...