1. Manuals
  2. Brands
  3. Megalarm Manuals
  4. Remote Starter
  5. COMMANDO EZ-2500
  6. Installation manual

Megalarm COMMANDO EZ-2500 Installation Manual

Remote engine starter with keyless entry system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
FEB/20/2003
COMMANDO EZ-2500
REMOTE ENGINE STARTER
WITH KEYLESS ENTRY SYSTEM
INSTALLATION MANUAL
550A
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the COMMANDO EZ-2500 and is the answer not in the manual?

Questions and answers

Related Manuals for Megalarm COMMANDO EZ-2500

Summary of Contents for Megalarm COMMANDO EZ-2500

  • Page 1 FEB/20/2003 COMMANDO EZ-2500 REMOTE ENGINE STARTER WITH KEYLESS ENTRY SYSTEM INSTALLATION MANUAL 550A...

  • Page 2: Installer Warnings

    FEB/20/2003 INTRODUCTION INSTALLER WARNINGS This Remote Starter with Alarm System is designed to be installed on fuel injected vehicles with an automatic transmission ONLY. Never install this remote starter on a manual transmission vehicle. This system must be installed and wired through a safety switch it will not start in any forward or reverse gear. Some automatic transmission vehicle [mainly older GM vehicles with a purple starter wire] have a mechanical-type park safety switch instead of electrical safety switch.

  • Page 3: Installation Diagram

    FEB/20/2003 INSTALLATION DIAGRAM 1. Red/White: Parking Light Relay Power input Indicator 2. White: Parking Light Relay Output One Way Transceiver 3. Black: Ground to Vehicle Frame Antenna 4. Brown: (-) 200ma programmable Output 1. Horn Output (Factory Default Setting) 2. Channel 3 Output Fuse 3.

  • Page 4: H1: 6 Pin Heavy Gauge Wiring Connection

    FEB/20/2003 #H5 5 PIN WHITE CONNECTOR FOR OUTPUT CONNECTION 1. Orange W ire: (-) 500mA Grounded Output W hen Armed 2. Yellow W ire: (-) 200 mA Ignition 3 Control Output 3. White W ire: (-) 200 mA Programmable output Dome Light Control Output (Factory Default setting) Or Channel 3 Output Or Key Sensor By-Pass Output...

  • Page 5: H2/3. Black Wire -- System Ground

    FEB/20/2003 VIOLET Wire Starter “On” Neutral Safety “Off” Switch “Start” “Acc” Ignition Switch Start Cut Relay Closed in Park or (When Used) Neutral Only H1/2 & H1/3. Red Wire (2)-- +12V Power Input Remove the two 20A fuses prior to connecting these wires and do not replace them until the satellite has been plugged into the control module.
  • Page 6 FEB/20/2003 Press the button at the same time to remote control the optional electrical device. The device will 'on' when the button(s) press continuously, and 'off' when the button(s) released. FACTORY SECURITY REARM SIGNAL OUTPUT– (See Alarm Feature I - 4 Programming) This wire is designed to rearm a factory installed security system.

  • Page 7: Gm Vats Key Override

    FEB/20/2003 1. You will need a transponder key that's already programmed to the vehicle. 2. Remove the trim around the ignition switch. 3. Wrap a thin (28 - 30awg) wire tightly around ignition switch 6 to 8 times and secure it. 4.

  • Page 8: Factory Security Disarm Signal Output

    FEB/20/2003 H5/4. PINK WIRE – (-) 200ma PROGRAMMABLE OUTPUT (See Alarm Feature I - 3 Programming) 2 STEPS UNLOCK OUTPUT (Factory Default Setting) -- The 2 steps unlock feature will work for the most fully electronic door lock circuit. The vehicle must have an electronic door lock switch (not the lock knob or key switch), which locks and unlocks all of vehicle's doors.
  • Page 9 FEB/20/2003 The WHITE/BLACK wire provides an instant shutdown for the remote start, whenever it is grounded. Connect the wire to the hood pin switch previously installed. This wire must be routed though a grommet in the firewall and connected to the hood pin switch. Important! This connection is a safety wire and must be connected as shown and tested as specifiled.
  • Page 10 FEB/20/2003 NEGATIVE TRIGGER DOOR LOCK SYSTE POSITIVE TRIGGER DOOR LOCK SYSTEM Blue Wire Door Unlock Blue Wire Door lock Locking Locking Master Master Green Wire Door Lock Green Wire Door Unlock Switch Switch + 12V To Exiting To Exiting Door Lock Relay Door Lock Relay VACUUM OPERATED CENTROL LOCKING 5-WIRE ALTERNATING DOOR LOCK...

  • Page 11: Programming Transmitter

    FEB/20/2003 2 STEP DOOR UNLOCK WIRE CONNECTION FOR 2 STEP DOOR UNLOCK WIRE CONNECTION FOR GROUND SWITCHED DOOR LOCKS POSITIVE SWITCHED DOOR LOCKS +12V H5/4: OEM Door Master Lock Switch OEM Door Master Lock Switch 6-Pin H5/4: Pink Wire Plug 6-Pin Pink Wire Unlock...
  • Page 12 FEB/20/2003 3 Press and release the transmitter button corresponding to the feature ‘Chirp on/off mode’ you wants to program. [1] LED flash, [1] chirp to indicate your are in features “Chirp on”. 4 Depress the transmitter button once to change the feature. [2] LED flash, [2] chirp to indicate your are in features “Chirp off ”.
  • Page 13 FEB/20/2003 REMOTE START FEATURE PROGRAM MODE. START FEATURE “ ” PRORAMMING: 1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2. Push the Valet switch 6 times and hold it until three chirps with a long chirp is hearing then release the valet switch. You are now in the Start feature ‘I’...

  • Page 14: Tachometer Checking Type

    FEB/20/2003 Exit : Press the button on the transmitter. A 3 long chirps & 3 parking light flashes to confirm exit. TACHOMETER CHECKING TYPE Enter Start Feature ‘II’ Programming Mode: 1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2.

  • Page 15: Return To Factory Default Setting

    FEB/20/2003 I. Press the button on the transmitter to stop engine running. You have been completed this programming successfully. II. Press button on the transmitter to exit the program mode. There will be 3 long chirps & 3 parking light flashes for confirmation.

  • Page 16: Shutdown Diagnostics

    FEB/20/2003 START FEATURE ALL RETURNS TO FACTORY DEFAULT SETTING: 4. Press the first, within 3 seconds press the button on the transmitter together for 6 seconds, there will be a confirmation six chirp with 3 long chirp to confirm the system “Start Feature I & II Programming all returns to factory default setting.

  • Page 17: Mechanical Neutral Safety Switch Considerations

    FEB/20/2003 concerning the Mechanical Neutral Safety Switch provided below will help you to determine if the vehicle you are working on has this type of safety switch and will provide alternate wiring methods to accommodate this situation. MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERATIONS: Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety when installing a remote start device.
  • Page 18 FEB/20/2003 METHOD 1 Ignition Key In Sensor Drivers Door Pin Switch Switch Closes with Key In Ignition Cylinder Key In Chime Module + 12V + 12 V Connected to (-) Negative 1N4003 To Hood Pin Switch Safety Safety Input Wire Shut Down (H6/4) White/ Black (H6/4) To connect to the key in sensor as shown in method 1:...
  • Page 19 FEB/20/2003 550A...

Table of Contents