Table of Contents
Advertisement
Quick Links
OPB480EV
1271 CFM 57.6V LI-ION POWERED WALK-
BEHIND LEAF BLOWER
USER MANUAL
DK2 USA WEST
3311 MEADE AVENUE STE
E DOCK 13, LAS VEGAS, NEVADA
89102 USA
Customer Service / Monday-Friday 8am-4pm EST / 1-888-277-6960
DK2 CORPORATE HEAD OFFICE
5330 MAINWAY
BURLINGTON, ONTARIO
L7L6A4 CANADA
LiFePO
4
ADVANCED LI-ION TECHNOLOGY
DK2 USA EAST
3750 SOUTH AVENUE
NORTH UNIT, TOLEDO, OHIO
43615 USA
www.dk2.com
Advertisement
Table of Contents
Summary of Contents for DK2 OPB480EV
- Page 1 1271 CFM 57.6V LI-ION POWERED WALK- BEHIND LEAF BLOWER USER MANUAL LiFePO ADVANCED LI-ION TECHNOLOGY DK2 USA WEST DK2 CORPORATE HEAD OFFICE DK2 USA EAST 3311 MEADE AVENUE STE 5330 MAINWAY 3750 SOUTH AVENUE E DOCK 13, LAS VEGAS, NEVADA...
-
Page 2: Warranty
Upon expiry of one (1) year, DK2 Inc. will have no further liability related to the product. DK2 Inc. does not authorize any party, including its authorized distributors or dealers, to offer any other warranty on behalf of DK2 Inc. -
Page 3: Online Resources
ONLINE RESOURCES LEARN MORE ABOUT YOUR PRODUCT Visit your product’s web page by visiting detailk2.com/shop- battery-power-equipment/p/opb480ev-k or scan the QR code on the left. PURCHASING REPLACEMENT PARTS In need of replacement parts? visit detailk2.com/shop-parts or scan the QR code on the left. -
Page 4: Table Of Contents
SCHEMATICS ............... 23 | OPB480EV man. -
Page 5: Technical Specifications
TECHNICAL SPECIFICATIONS MODEL NUMBER OPB480EV BATTERY 57.6V Max, 1,024Wh, 20Ah LiFePO MOTOR 2,000W (4,000W Max) 3,500 RPM cordless brushless EV-grade motor 4.1 ft/lb (5.5 Nm) rated TORQUE 18.4 ft/lb (25 Nm) peak CHARGER 120V AC/DC 200W MAX AIR FLOW 150 mph (241.4 km/h) SPEED 215 ft/sec (65.5 m/sec) -
Page 6: Section I • Safety
SECTION I • SAFETY... -
Page 7: Safety Conventions
SAFETY CONVENTIONS DANGER! This indicates a hazardous situation, which, if not avoided, will result in death or serious injury. WARNING! This indicates a hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION! This indicates a hazardous situation, which, if not avoided, may cause minor or moderate injury. -
Page 8: Safety Decals
SAFETY DECALS Make sure all safety warning decals are attached and in readable condition. Please call DK2 at 1 (888) 277-6960 if you need help replacing missing or defaced safety decals. WARNING / ATTENTION (EN) Read carefully and understand all 57.6V Li-ion BLOWER... -
Page 9: General Safety Information
GENERAL SAFETY that will protect your feet and improve your footing on slippery surfaces. INFORMATION CAUTION! Exercise caution to avoid slipping or falling. WARNING! Keep guards in place and in WARNING! Always wear working order. Never protection. Following this rule will operate the tool with reduce the risk of serious personal any guard or cover... -
Page 10: Understand Your Machine
WARNING! Do not use tool if switch WARNING! This machine is not a toy, does not turn it off. Have the switch and is to be used only for its intended replaced by a qualified service center. purpose. Therefore, exercise extreme | OPB480EV man. -
Page 11: Inspect Your Machine
caution at all times. This machine has been designed to perform one job: CAUTION! Do not tamper with the blow debris and leaves from lawns, motor and/or battery in an effort driveways, parking lots, etc. Do not to get it to run at higher speeds. use it for any other purpose. - Page 12 Never operate machine without directional discharge opening and impeller guard properly affixed to the machine. These devices shield the operator from accidental contact with the rotating impeller. DANGER! Exercise extreme caution when operating on or crossing gravel | OPB480EV man.
-
Page 13: Getting To Know Your Machine
GETTING TO KNOW YOUR MACHINE Handle Battery Battery & Motor Shroud Motor Housing Front wheel assembly Rear wheel assembly Adjustable deflector Base Axle v.230518 |... -
Page 14: Section Ii • Assembly
SECTION II • ASSEMBLY... -
Page 15: Step 1: Front Wheel Rack Assembly
STEP 1: FRONT WHEEL RACK ASSEMBLY 1. Insert the rotating shaft of the wheel rack (3) into the sleeve of the support frame (5). 2. Secure with M8x45 flange bolt and M8 flange nut (6) to complete the front wheel assembly (F) v.230518 |... -
Page 16: Step 2: Wheel Rack Installation
STEP 2: WHEEL RACK INSTALLATION Fix the front wheel assembly (F) to the housing (E) using an M8 hex nut (4). | OPB480EV man. -
Page 17: Step 3: Rear Wheel Installation
STEP 3: REAR WHEEL INSTALLATION Install the 10” rear wheels (31) on both sides of the axle (J) and secure using the provided R-pin (32). v.230518 |... - Page 18 1. Secure the top handle (34) to the bottom handle (33) using M8x45 hex bolts (6) and M8 hex nuts (4). 2. Secure the assembled handle to the machine using M8x45 hex bolts (6) and M8 hex nuts (4). | OPB480EV man.
-
Page 19: Section Iii • Operation
SECTION III • OPERATION... -
Page 20: Starting The Machine
1. Turn the switch key on the side of the battery and motor shroud to stop the motor (FIG. 3). 2. Press the power button on the battery to turn off the power supply (FIG. 4). The machine will stop completely. FIG. 3 FIG. 4 | OPB480EV man. -
Page 21: Section V • Parts & Schematics
SECTION V • PARTS & SCHEMATICS... -
Page 22: Parts List
Housing front panel OPB480EV33H23 Top handle OPB480EV14H23 Housing base OPB480EV34H23 Bottom handle OPB480EV15H23 5/16UNFx1 hex bolts OPB480EV35H23 Shroud OPB480EV17H23 Ø8 spring washer OPE100 Battery OPB480EV18H23 Ø8 flat washer *Battery (36) sold separately unless kit model (OPB480EV-K) is purchased. | OPB480EV man. -
Page 23: Schematics
SCHEMATICS v.230518 |...
Need help?
Do you have a question about the OPB480EV and is the answer not in the manual?
Questions and answers