Hessaire HTH01 Quick Start Manual

Wifi evaporative cooler line-voltage thermostat

Advertisement

Quick Links

Installation

WARNING: High Voltage can cause serious injury or death.
Control must be installed by a qualified electrician. Turn off
all power before starting installation.
CAUTION: Follow all local building / electrical codes
CAUTION: Do not attempt to repair or service control.
Components are not serviceable.
WARNING: Failure to follow instructions and warnings may
lead to property damage or personal injury.

Electrical Ratings

INPUT
WHITE/COM
RED POWER
BLACK:
(L2)
(L1)
FAN HIGH
115Vac: 60Hz,
115Vac: 60Hz, 15.2A
14.0A, 1Hp
230Vac: 60Hz,
230Vac: 60Hz, 7.8A
7.0A, 1Hp

Mounting Control To Wall

Control is designed to mount in an electrical box
WARNING: Make sure all power is off.
Locate position on wall in area that is convenient to access and
control your evaporative cooler.
Use qualified electrician to install thermostat, run proper sized
wiring and correctly make all connections.
Once all connections are properly made and control is secured
to electrical box, power can be turned back on.

Troubleshooting

Issue
Possible Cause
Incorrect wire connections
Cooler won't turn
Circuit breaker off
on / display off
Control faulty
Bad wire connection
Motor failed
Fan / pump not
turning on
Pump failed
Control faulty
HTH01 Instruction 030923
AC115V / 230V 60HZ
OUTPUT
YELLOW:
BLUE:
FAN LOW
PUMP
115Vac: 60Hz,
115Vac: 60Hz,
9.0A, 1/3Hp
1.2A, 1/40Hp
230Vac: 60Hz,
230Vac: 60Hz,
4.5A, 1/3Hp
0.8A, 1/40Hp
.(sold separately)
Action
Check connections
Reset breaker
Replace control
Check connections
Replace motor
Replace pump
Replace control
www.hessaire.com
WiFi Evaporative Cooler Line-Voltage Thermostat
Volts: 115 / 230
Operates all standard evaporative
coolers
Use with standard 2-speed cooler
motors up to 1 HP
WiFi Control
Auto Set Temperature
Or Override With
Manual Setting
2-Speed Standard
Cooler Motor
Up To 1HP
Pump Controlled
Independently
Automatically
Pre-Wet In
"Auto" Mode
Control Operation

Automatic Mode:

Press and hold MODE button for 2 seconds to select Auto MODE. Use the
temperature arrow setting buttons to set the desired temperature. There will
be a 2 minute "Pre-Wet" cycle which turns only the pump on to wet the media
before the fan turns on. If the room temperature is 4°F higher than the set
temperature, the fan will start on high(Hi) speed. When the room temperature
drops within 2°F of the set temperature, the fan will enter low(Lo) speed until
the set temperature is reached. Both the fan and pump will shut off at this
point. Pressing the fan speed button can also manually set the fan speed in
Auto MODE. The pump cannot be independently turned off in Auto MODE.

Manual Mode:

Press and hold MODE button for 2 seconds to select Manual MODE. In this
mode, the pump can be turned on or off independently. The fan speed can
also be selected independently. The thermostat will not shut off the function
of the cooler in Manual MODE.

Timer:

The timer function is used to turn off the cooler after a set period of time. To
operate the timer function, push the "clock" button to enter the timer setting.
The humidity display box will switch to show the timer display. Use the up
and down arrows to set the desired delay time.
MODEL: HTH01
Features
Large, easy to read digital displays
Relative Humidity % readout
Delayed off timer up to 12 hours
Fits in single gang wall box

Control Functions

Large, Easy
To Read
Temperature
Dispays
Displays Relative
Humidity In Room
When Timer Is
Not In Use. 12 Hr
Delay Timer Can
Be Set In Hour
Increments
(WiFi Set Up On Back)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HTH01 and is the answer not in the manual?

Questions and answers

Summary of Contents for Hessaire HTH01

  • Page 1 The humidity display box will switch to show the timer display. Use the up turning on Pump failed Replace pump and down arrows to set the desired delay time. Control faulty Replace control (WiFi Set Up On Back) HTH01 Instruction 030923 www.hessaire.com...
  • Page 2 Make your device discoverable by holding the fan button for 5 seconds. The internet symbol will flash on your controller. Select the “+” to add a device. Select the Hessaire logo and you will be asked to re-enter your WiFi passcode. You will receive a message: “Added Successfully”.

Table of Contents