Related Manuals for Provision ISR PoES-16250CL+2G+2SFP
Summary of Contents for Provision ISR PoES-16250CL+2G+2SFP
- Page 1 Color LCD PoE Switch ● PoES-16250GCL+2SFP PoES-16250CL+2G+2SFP ● PoES-24370GCL+2SFP PoES-24370CL+2G+2SFP User Manual...
- Page 2 P a g e COLOR LCD POE SWITCH USER MANUAL Notes Before operating the switch, we strongly advise users to read this manual and keep it for later use. Please use the supplied power cord. Avoid incorrect operation, shock, vibration or heavy pressing which can cause damage to the switch. Do not use corrosive detergent to clean the body of the switch. If necessary, please use a soft dry cloth to wipe dirt; for hard contamination, use neutral detergent. Any cleanser for high‐grade furniture is applicable. Do not operate the switch in extreme temperatures or extreme humidity conditions. Keep away from heat sources such as radiators, heat registers, stove, etc. The instructions in this manual could be outdated; if you need any clarifications you can contact an authorized PROVISION‐ISR technician. PROVISION‐ISR reserves the right to add changes to this manual and publish it online on our website (www.provision‐isr.com): there may be inconsistencies with the latest version. This applies to any and all software upgrades and product improvements, interpretation and modification added. These changes will be published in the latest version without prior notification. All pictures and examples used in the manual are for reference only. Package Contents Check the following contents of your package: PoE Switch x 1 User’s Manual x 1 Power Cord x 1 ...
-
Page 3: Table Of Contents
P a g e COLOR LCD POE SWITCH USER MANUAL Table of Contents 1) Introduction ........................ 4 2) Hardware Description ..................... 4 2.1) Front Panel: ...................... 4 2.2) Rear Panel ...................... 5 3) LCD Features: ...................... 6 3.1) General Status Indicators: ................ 6 3.2) General Warnings: ..................... 6 3.3) ... -
Page 4: Introduction
P a g e COLOR LCD POE SWITCH USER MANUAL 1) Introduction Thank you for choosing Provision‐ISR’s PoE Switch. The 16/24GE(PoE)+2G SFP LCD Display PoE switch have 16(24)‐10/100/1000Mbps PoE RJ45 Port and 2‐Gigabit SFP Slot. Its PoE ports can automatically detect and supply power with those IEEE 802.3af/at compliant Powered Devices (PD). The electrical power is transmitted along with data in one single cable allowing you to expand your network where there are no power lines or outlets, where you wish to fix devices such as AP, IP Cameras or IP Phones, etc. The LCD can be used to display the PoE work status, accurate measurement total load and for each port independently. This can help the installer and engineer to quickly discover and solve network failures and improve work efficiency and quality. Port Feature Model PoE Ports PoE Ports Speed Uplink Ports Uplink Ports Speed PoES‐16250GCL+2SFP ... -
Page 5: Rear Panel
P a g e COLOR LCD POE SWITCH USER MANUAL 10/100Mbps Switches Front panel illustration. General Information Menu ‐‐‐M 631M 13.4 W ‐‐‐M 920M OLP ‐‐‐M 921M 18.9 W 856M 856M ULP ‐‐‐M ‐‐‐M ‐‐‐‐ W 238M 238M Enter SCP 125M ‐‐‐M ‐‐‐M ‐‐‐M 2.2W ‐‐‐M ‐‐‐M 23.3 W 323M 323M 23.7 W ‐‐‐M ‐‐‐M 5.8... -
Page 6: Lcd Features
P a g e COLOR LCD POE SWITCH USER MANUAL LCD Features: This PoE switch line is equipped with color LCD display and PoE. The LCD can display the status of the switch as well as independent status for each of the PoE ports such as: Output power, Overload, Short circuit, Light load, Low voltage, Over voltage, High temperature Etc. 3.1) General Status Indicators: 1) Port Number. Remaining ports will be displayed in the next page. 2) Port power consumption 3) Port download real‐time bandwidth. 4) Port upload real‐time bandwidth. 5) PB: the total “PoE budget” of the switch 6) TP: “Total power” under current use 7) PD: Numbers of “PD device” 8) Norm: ... -
Page 7: Port Status Warnings
P a g e COLOR LCD POE SWITCH USER MANUAL 3.3) Port Status Warnings: General Information Switch Port Information OLP (Overload Protection): The port is overloaded ‐‐‐ M 631 M ‐‐‐ M 631 M 13.4 13.4 W ‐‐‐ M 920 M W ‐‐‐ M 920 M OLP OLP and was shut down. ‐‐‐ M 921 M ‐‐‐... -
Page 8: Port Bandwidth Limit
P a g e COLOR LCD POE SWITCH USER MANUAL 3) CCTV Mode: CCTV mode will enable “Fixed VLAN” together with restricting the downlink port bandwidth to 10Mbps duplex communication. The CCTV mode allows the installer to reach distances of up to 250m over standard Cat.5e cable. 3.4.2. Port Bandwidth Limit: Port Bandwidth Limit This feature allows you to monitor and restrict the incoming Options: bandwidth coming from a single port. Once crossed, the switch < Disabled will set a buzzer alarm to warn for bandwidth overuse. Once 400Mbps enabled, this setting will take effect on all downlink ports. It 500Mbps cannot be set for a specific port. 600Mbps The default setting is “Disabled” meaning that there is no Port1~Port24 valid! bandwidth restriction. The other options are 400Mbps, < U P > / < D o w n > : S e l e c t <... -
Page 9: Pse Power Adjust
P a g e COLOR LCD POE SWITCH USER MANUAL Interval (60~300s): The interval is the allowed time without incoming/outgoing traffic from the PD. Once no traffic is detected, the countdown will commence according to the configuration. If there is still no traffic by the countdown reaches 0 the switch will execute a hard bootup procedure. Power Off (5~60s): This value determines the duration of the power cut for the required switch. After this countdown reaches 0, the switch will restore power to the port and let the PD device boot and initialize. 3.4.5. PSE Power Adjust: The PSE (Power Source Equipment) is the main power supply unit for the switch. In order to increase its life and reliability its rate is actually higher than the stated power bank, but it is reserved for situations where PD power requirement suddenly peaks for a short moment. In case the devices connected to the switch reaches the PB PSE Power Adjust limit, you can manually increase it and utilize more power to the PoE ports on the expense of the reserve power. Options: Add 5% (105% PB) This feature has 4 options: Add 10% (110% PB) 1. Normal (100%) Add 15% (115% PB) Note: 2. Add 5% (105% PB) TP must be less than PB! < U P > / < D o w n > : S e l e c t 3. -
Page 10: Pse Port Condition
P a g e | 10 COLOR LCD POE SWITCH USER MANUAL The priorities are as follows: Critical: Devices set to “Critical” will shut down last High: Device set to “High” will shut down once all the “Low” priority devices as shut down. Low Priority (Default Settings): These devices will shut down first. 3.4.7. PSE Port Condition: PSE Port Condition This setting will determine whether the switch is allowed to distribute PoE to the specified channel. This setting is mainly Port Status useful after the initial setting of the network and the PD < Enable devices. After the system is up, all ports without PD devices Disable and all unused ports should be disabled from receiving PoE. It will prevent overloading the system by unrequired PoE devices. “Enable” is the default setting. This setting will only affect PoE and will not affect network communication. 3.4.8. PoE Port Power: This setting can limit the power supplied to a specific port as required. Each port can be configured independently. 1) Port: Port number for configuration. 2) Power (6‐36W): The power limit for the port. Skips in 2W intervals. Note: PoE Port Power is available for configuration only if the PD type is set to “Enhanced”/”Legacy”. If the PD type is set to “Standard” the PoE Port Power is automatically set to 32W and cannot be ... -
Page 11: Lcd State
P a g e | 11 COLOR LCD POE SWITCH USER MANUAL 3.4.9. LCD State: This setting will determine the duration of which the LCD LCD State monitor will stay on. The options are as follows: Turn off after: 1) Never (Always On): The LCD monitor will stay on. Never (Always On)< 2) 10 min (Default Setting): The LCD will turn off after 10 min 10 minutes. 20 min 30 min 3) 20 min: The LCD will turn off after 20 minutes. 4) 30 min: The LCD will turn off after 30 minutes. < U P > / < D o w n > : S e l e c t ... -
Page 12: About
P a g e | 12 COLOR LCD POE SWITCH USER MANUAL 3.4.12. About: This will show you general information about the PoE Switch. About Thank you for choosing Provision‐ISR Model:PoES‐24380GCL+2SFP HW Ver.:V3.0 SW Ver.:V1.20 Switch Installation: This section describes how to install your Ethernet Switch in the best manner and make proper connections. Please follow the following instructions in avoid of incorrect installation which might cause device damage and potential security threat. General Instructions: Do not place the switch near water or any damp area. Prevent water or moisture from entering the switch chassis. Do not place the switch on an unstable case or desk. The switch might be damaged severely in case of a fall. Ensure proper ventilation of the equipment room and keep the all the ventilation openings of the switch free of obstruction. Make sure that the operating voltage and current matches the power input labeled on the switch. Do not open the chassis while the switch is operating or when electrical hazards are present to ... -
Page 13: Rack Mount Installation
P a g e | 13 COLOR LCD POE SWITCH USER MANUAL 4.2) Rack Mount Installation The switch is rack‐mountable and can be installed on any EIA‐19 compatible rack. Before installation, please install the mounting brackets on the switch side panels (one on each side), secure ... -
Page 14: Turning On The Switch
P a g e | 14 COLOR LCD POE SWITCH USER MANUAL Step 2: Mounting the switch on the rack. 4.3) Turning on the switch Please plug the power supply into the switch, the internal power system of the switch can Auto‐ regulate the working power according to the actual input power. When the switch is power on, the power indicator will be light on the front panel of the switch shines. Note: Please confirm the voltage is correct before power on, otherwise the switch will be damaged. (There is a power supply socket on the back panel of the PoE Ethernet switch. The power input is: 100V‐240Vac, 50/60Hz.) ...
Need help?
Do you have a question about the PoES-16250CL+2G+2SFP and is the answer not in the manual?
Questions and answers