Subscribe to Our Youtube Channel
Summary of Contents for lilitab SmartDock Connect G40SC-C
- Page 1 Quick Start Guide v1.00 Model G40SC-C (USB-C) Model G40SC-L (Lightning) Lilitab LLC 39B Larkspur Street San Rafael, CA 94901 Phone: (888)705-0190 support@lilitab.com...
- Page 2 • Consult the dealer or an experienced radio/TV technician for help. Changes or modifications made to the Device Name device not expressly approved by Lilitab LLC could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
-
Page 3: Table Of Contents
Table of Contents Introduction .......................... 4 Hardware Setup ........................5 Installing KMS and Registering a Tablet ....................5 Installing the SmartDOCK Connect Module ....................6 Pairing with the SmartDOCK Connect Module ..................7 Firmware Update ............................8 Registering a SmartDOCK in KMS ......................8 Software Unlock with KMS .................... -
Page 4: Introduction
SmartDOCK Connect is a communication module that provides Bluetooth connectivity between a tablet and a Lilitab SmartDOCK mount (sold separately). Lilitab Head Units with an installed SmartDOCK Connect module can electronically unlock a SmartDOCK mount from the software interface, without a physical key, facilitating remote access control, device mobility, and tablet sharing. -
Page 5: Hardware Setup
Installing KMS and Registering a Tablet To set up a tablet to work with SmartDOCK Connect, you will first need to install and configure Lilitab KMS. This will generally be done by a system administrator, an authorized representative of that administrator, and/or the person responsible for the tablets and kiosks at a given location. -
Page 6: Installing The Smartdock Connect Module
Step 1: Installing the SmartDOCK Connect Module Tools Needed: T10 Pin-Torx Wrench (provided) Step 1: If tablet installed and latch security screws present, remove latch screws with wrench. If no tablet installed, skip to Step 3. Step 2: Pinch the latch release (at center rear of head unit) together with one hand while sliding the faceplate towards the rear camera opening with the other. -
Page 7: Pairing With The Smartdock Connect Module
Pairing with the SmartDOCK Connect Module Step 1: The next step is to pair the tablet with the SmartDOCK Connect Module. The tablet uses this module to communicate with the SmartDOCK when the tablet is docked. Before beginning the pairing process, check tablet settings and make sure that Bluetooth is turned on. -
Page 8: Firmware Update
Firmware Update Firmware Update: Once the dock is communicating with a tablet via the SmartDOCK Connect module, the system may automatically update the dock firmware, if such update is needed. This process will take about 60 seconds. For best performance, allow the firmware update to proceed without disturbing the tablet or dock. -
Page 9: Software Unlock With Kms
Software Unlock with KMS Unlock Button Using the Unlock Button Once a tablet has been paired with the SmartDOCK Connect module and docked to a SmartDOCK, the dock can be unlocked by pressing the blue “Press to Unlock” button in the KMS header. KMS-enabled Dock Configuration Panel apps can be configured to use the Unlock Button directly, or to access a PIN Pad interface for secure unlock. -
Page 10: Appendix A: Kms System Setup
Appendix A: KMS System Setup This appendix will explain the basics of the initial setup a Lilitab KMS deployment. This is intended as a minimalist, “quick start” treatment of the subject. For more detailed instructions about KMS, including comprehensive information about platform features, accessories supported, system settings, and administration tools, consult the Lilitab KMS User Guide. -
Page 11: Creating A New Enterprise
Step 1: Creating a New Enterprise If this is the very first tablet in your company to use Lilitab KMS, you will need to create a unique Enterprise ID for your company. Generally, the person to create a new Enterprise ID will be a... -
Page 12: Creating A New Group
Step 1: Creating a New Group Lilitab KMS refers to a local network of kiosks, generally in the same business location, as a “Group”. Each Enterprise will have multiple Groups, one at each location, and each Group reports to the Enterprise. -
Page 13: Adding A Tablet To A Group
Step 1: Adding a Tablet to a Group Once an Enterprise and one or more Groups have been created, additional tablets can easily be added to a Group. To add a new Tablet to an Existing Group: Step 1: Enter the Enterprise ID and Group ID of the Group to Step 2: which the tablet will be added. -
Page 14: Appendix B: Accessing The Admin Portal
KMS Settings (in iOS Settings) and turn on “Show KMS Controls”. App Step 2: Step 2: Press the “Lilitab KMS” logo at the right end of the footer. This will take you to the portal login screen. Step 3: Log in to the portal by providing your admin Username and Password. -
Page 15: Appendix C: Bluetooth Pairing Status/Troubleshooting
Appendix C: Bluetooth Pairing Status/Troubleshooting If you are having trouble with the Bluetooth connection between the tablet and SmartDOCK Connect module, the first thing to do is dock the head unit. When the head unit is docked, the tablet should automatically connect to the module and begin communicating. -
Page 16: Unpairing A Smartdock Connect And Tablet
Unpairing a SmartDOCK Connect and Tablet Step 1: A tablet can only be paired with one SmartDOCK Connect module at a time. To change pairing, the tablet will need to be unpaired with the first SmartDOCK Connect before it can be paired to another. -
Page 17: Removing Stale Bluetooth Connections
Connect” under “My Devices”. Tap on the “Information Icon” to open device properties. Step 2: This will open device properties. Here tap “Forget This Device”. Step 3: Repeat Step 1 and Step 2 until all “Lilitab SmartDOCK Connect” devices have been removed from the “My Devices” list. -
Page 18: Appendix D: Smartdock Troubleshooting
Tap in the background area of the app switcher to return to the Home Screen. • Relaunch the KMS-enabled app by tapping the app icon on the Home Screen. If more help is needed, please contact Lilitab Product Support at support@lilitab.com http://www.lilitab.com/pages/support... -
Page 19: Appendix E: App Settings
Used to allow app to monitor geofence and continue Background App Refresh updating server when in background Below the Access Settings are the Lilitab KMS Settings, which allow tablet users to access UI features which may help with administration and debugging at the tablet. Recommended... -
Page 20: Appendix F: Portal Settings
Appendix F: Portal Settings Enterprise Settings, Dock Config Panel: The following settings at the Enterprise and Group levels influence the appearance and behavior of SmartDOCK Unlock Controls. To access the portal, see Appendix B. Allow Web Unlock: When selected, this setting allows javascript access to SmartDOCK unlock methods.
Need help?
Do you have a question about the SmartDock Connect G40SC-C and is the answer not in the manual?
Questions and answers