Hatsuyuki HB600A Instruction Manual

Block ice shaver

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

INSTRUCTION MANUAL

BLOCK ICE SHAVER

MODEL: HB600A

Table of Contents

Need help?

Do you have a question about the HB600A and is the answer not in the manual?

Questions and answers

Summary of Contents for Hatsuyuki HB600A

Page 1 INSTRUCTION MANUAL BLOCK ICE SHAVER MODEL: HB600A ...
Page 2: For Safety
FOR SAFETY ●Before operating the machine please read the following "Instructions for Safety" in the manual very carefully, and operate the machine correctly. ●Each instruction specified in the manual is very important for safety, so be sure to follow ...
Page 3 WARNING ●Do not pour water over the machine or immerse ●In the event of circuit breaker moving to “OFF” machine in water. position, please contact the machine vendor. It can cause a short circuit Switching breaker to or electric shock, as well “ON”...
Page 4 CAUTION ●Never use inflammable sprays near the machine ●Always install the machine on a stable and flat and never place volatile or inflammable materials surface. close to the machine. Irregular or imperfect installation can cause the Sparks from the unit to tip or fall and is switch could possible therefore dangerous.
Page 5 Shaft Cover (Accessary) To cover the main shaft for Tension Adjusting Bolt safety. To adjust the power to press ice. Power Switch To switch on and off. Crank Handle (Accessory) To raise/lower the shaft and ice holder. Main Shaft It rotates during operation, and transmits the power to Fixing Screw for Crank press the ice. Ice holder is Handle (Accessory) mounted on the lower end. To fix the crank handle to the main unit. Shaving Chamber Place a block ice in the Sliding Cover Chamber for shaving ice. Safety shaving starts when this cover is completely closed. Blade Adjustment Knob Ice Holder To turn the knob to control It has spikes on the bottom to texture of the shaved ice. grip ice. Blade Grounding Wire To shave the ice. Be sure to arrange grounding work to avoid electric shock Shaving Table Place for ice to be shaved.
Page 6: Check Before Operation
Check before Operation Attach the enclosed crank handle in the following manner. 1) There is an opening on the right side of the head cover. Attach the crank handle to the body through the hole to connect the worm shaft inside.
Page 7: Operation
Operation Plug in the shaver. Make sure that power switch is turned to off position before plugging in the unit. Slide the sliding cover to the right to open. Turn the crank handle clockwise to raise the ice holder. Make sure that the ice holder does not descend when the crank handle is free from your hand.
Page 8 Prepare a cup under the shaving table to receive the shaved ice. Switch ON. Shaving ice begins. Adjust the texture of shave ice. Turn the blade adjustment knob for the desired texture. For finer texture, turn the knob clockwise. or turn it counterclockwise for coarser.
Page 9 Taking the ice from the shaving table Do not touch the blade tip in placing and taking out ice. It could cause injury. Do not touch the prongs of the ice holder. They could cause injury. 1) Switch the unit off. And turn the crank handle clockwise to raise the ice holder.
Page 10: About Protector
About Tension Adjustment Bolt Adjust the tension adjustment bolt not to descend when you remove supporting hand from the holder. Otherwise it could cause injury. It adjusts the power to hold the ice. -Use a slotted screw driver. -Turn the tension adjusting bolt clockwise for stronger tension of gripping ice or counterclockwise for weaker.
Page 11 6) Pull the blade upward through the opening of the shaving table. 7) Position a new blade that the engraved mark "初雪(Hatsuyuki in Japanese)” faces the ice holder. And insert it between the blade holder and the ice receiver from the opening of the shaving table.
Page 12: Daily Maintenance
Maintenance Be sure the unit switched off and unplugged before cleaning. Wear protective gloves when cleaning the inside of the chamber and when changing blades. Do not touch the blade tip directly. Be sure to lower the blade below the surface of the shaving table when cleaning the inside of the shaving cabinet, and wipe the table counterclockwise (against the blade tip direction).
Page 13: Monthly Maintenance
How to Detach/Attach the Sliding Cover 1) Move the sliding cover to the right until its triangle mark meets the triangle mark on the head cover. 2) In the position that both triangle marks meets, pull out the sliding cover to the front to remove it. Cleaning the heavy dirt on covers - Wipe covers by a dry soft cloth.
Page 14: Yearly Maintenance
5) Mount the head cover and assemble the crank handle into the crank handle shaft. Put the gear oil to lubricate bearing and the main shaft while moving the main shaft up and down. After lubrication, mount the shaft cover. (Refer to the explanation of the shaft cover on page 5.) Yearly Maintenance Periodically confirm there is no dust on the plug prongs and blade attachments.
Page 15: Troubleshooting
Trouble Shooting - The machine should be serviced and repaired by authorized mechanic or the distributor. A) The machine does not start. Is the plug connected to the socket? Connect to the socket. Is the protector working? See page 9 – About Protector. Is the belt mounted properly? Contact the distributor.
Page 16: Specifications
Specifications Type Block Ice Shaver Mode No. HB-600A Power AC115V, 1ph., 60Hz AC230V, 1ph., 50/60Hz. Rating Power Consumption 225 / 230 / 205W Shaving Capacity 1.8/2.2kg/minute Max. Shaving Diameter 213mm Unit Dimensions (W) 348mm X (D) 477mm X (H) 896mm ( 710mm up to the head cover ) Weight 19kgs.