Panasonic CF-28 Supplementary Instructions Manual page 7

<For models with LAN port>
14
Select [Cancel].
<For models with modem port>
Follow the on-screen instructions and install modem
driver.
(At the [Modem Board Installation Wizard], select
[Next]. Confirm [MP3930V-W(C) Modem] is dis-
played when "The wizard will install the modem driver
shown below" is displayed on the screen and select
[Next], then select [Finish].
15 Follow the on-screen instructions and install Phoenix
APM 2.0 for Windows NT.
When the installation completes, select [Don't Restart
now].
Follow the on-screen instructions and install Phoenix
16
Card Executive for Windows NT.
When the installation completes, select [Restart now].
When the message [Press <F2> to enter SETUP] is dis-
17
played, press F2
and then run the Setup Utility.
If the password has been set, enter the Supervisor Pass-
word.
Press F9 .
18
At the confirmation message, select [Yes] and press
Enter . (The Setup Utility settings will return to their
default values. Even the security settings with the ex-
ception of the password(s) will return to their default
values.)
Change the settings where necessary.
Press F10 .
19
At the confirmation message, select [Yes] and press
Enter .
20 The [Begin Logon] display will appear. Perform the
operation in step .
11
Press Fn + Tab on viewing [Card Executive 2.0
21
for NT Diagnostics] and check whether
If so, select [Next].
Select [Next], then select [Finish].
22
Windows will restart.
The [Begin Logon] display will appear. Perform the
23
operation in step 11 .
Add the check mark to [Install system provided driver
24
for this card] and press [OK].
Follow the on-screen instructions.
If [Service Control Manager] is displayed, press [OK].
Install Service Pack 6 after the Windows setup com-
pletes ( "Technical Information").
Select [Change] in [Start] - [Settings] - [Control Panel]
25
- [Mouse] - [General].
Press [Have Disk] and input [c:\util\drivers\mouse], then
26
press [OK].
Confirm [Touchpad/Touchscreen] is selected, then press
27
[OK].
If [Confirm Device Install] is displayed, press [Yes].
Press [Close].
28
The display will ask you to restart Windows, press [Yes].
The [Begin Logon] display will appear. Perform the
29
operation in step
Double-click the [Internet Explorer] icon to install
30
Internet Explorer.
Select [I accept the agreement], then select [Next].
31
32 Select [Install Minimal, or customize your browser],
then select [Next].
Select [Full] by clicking
33
34 At the [Restart Computer], select [Finish].
The [Begin Logon] display will appear. Perform the
35
operation in step
36 Set the correct settings for all items in [Control Panel]-
[Regional Settings] and [Date/Time] etc.
37 Install the Acrobat Reader. (
tions")
38 Turn the computer off and replace the floppy disk drive
with CD drive.
39 Turn the computer on and logon as the Administrator.
Set the CF-WWL282 Driver CD-ROM in the CD drive.
40
Create"c:\util\drivers\aironet" folder. Select [Start] -
[Programs] - [Command Prompt] and input the follow-
ing.
xcopy d:\ * . * c:\util\drivers\aironet /s
("d" is the CD drive letter. You can change the letter
to suit your preference.)
Install the Aironet Client Utility (ACU).
41
The Aironet Client Utility (ACU) is used to configure
your client adapter for use in a wireless enterprise and
perform user-level diagnostics on your client adapter.
In [Start]-[Run], input [c:\util\drivers\aironet\utilities\acu\setup.exe]
and press [OK].
42 <Only for models with LAN port>
1) Select [Add] in [Start] - [Settings] - [Control Panel] -
[Network] - [Adapters] .
2) Select [Have Disk].
Input [c:\util\drivers\lan] and then select [OK].
3)
is displayed.
4) Select [Intel(R) PRO Adapter] and then select [OK].
Select [Close] and follow the on-screen instructions.
5)
In [Start]-[Settings]-[Control Panel]-[Network], make
43
necessary change.
The settings will vary for different network environments
depending on the network system being used. For more
details, ask your system administrator or the person in
charge of the network.
44 Remove the CD-ROM and turn the computer off, then
replace the CD drive with floppy disk drive.
NOTE
If the cursor can not be pointed correctly with
your finger, perform [Calibration] in [Start]-[Set-
tings]-[Control Panel]-[Mouse]-[TouchScreen].
11 .
, then select [Next].
.
11
"Operating Instruc-
Enter
7