Table of Contents
Advertisement
Other Information
Running the System Test
The System Test allows you to run a basic diagnostics check on your digital satellite receiver. If you are experiencing any trouble with your receiver, run
the system test. It will also allow you to get your access card and receiver ID numbers or to initiate diagnostic procedures on your digital satellite receiver.
First make sure that:
• all connections—jacks, cables, etc.—are correctly in place. See Chapter One, Setup and Connections, for more information,
• there are batteries in the remote control, and they are working correctly,
• the access card is installed in the digital satellite receiver.
Follow these steps to run the diagnostics system test on your digital satellite receiver.
1. Turn on your TV and the digital satellite receiver.
2. Press the DIRECTV button to put the remote control in satellite receiver-controlling mode, then press MENU to bring up the Main menu.
3. Select System Setup.
5. Select System Test.
6. If your system does not pass the system test, check any of these potential trouble areas: cabling, pointing the satellite dish, phone connection, and
access card.
7. If you continue to have problems, call RCA Customer Service at 1-800-679-4776.
You should run a system test several times before concluding that there is a problem. Occasional fluctuations in the phone line or satellite signal can
give temporary false readings.
Fine-Tuning the Signal
If you self-installed your satellite dish antenna, you may have already used the Assisted Setup to find the dish-pointing coordinates, acquire and fine-
tune the signal, and run a system test.
If you need to run the Assisted Setup again, select System Setup from the Main menu, then select Assisted Setup.
If you just want to check your dish-pointing coordinates or run the signal strength meter, select System Setup from the Main menu, then select Dish
Pointing.
Finding the TV's Video Line Input
TV Button
Note: If your TV is connected with just coaxial cables, you only need to tune to channel 3 or 4.
If you used audio/video cables to connect your TV to the digital satellite receiver, you must tune your TV to the video input
VCR
ON OFF
TV
channel to view DIRECTV
DVD
AUX1
AUX2
DIRECTV
there are brands and models of TVs. Below are some things you can try.
MUTE
SKIP
• If your TV brand is RCA, GE, or PROSCAN, press TV on the remote control that came with your digital satellite receiver.
+
CH
• If your TV brand is not RCA, GE, or PROSCAN, consult your TV Owner's Manual.
If you cannot find your TV Owner's Manual, you will have to investigate. You might access the TV's video input channel by:
CH -
FETCH
GO BACK
GUIDE
INFO
• pressing a button on the remote control
(-)
• finding it through the TV's menu system
• tuning directly to it by pressing a specific channel number
MENU
CLEAR
• going through all channels in the list by pressing the channel up or down buttons on the TV.
1
2
3
The box below lists of some of the different ways manufacturers label the video input channel.
4
5
6
7
8
9
ANTENNA
WHO INPUT
0
STOP
PAUSE
WHO•INPUT Button
40
®
programming and menus. There are just as many ways to access a TV's video input channel as
Then press the WHO•INPUT button on the remote.
i
V
B u t t o n / s w i t c h
o n t h
e T V
I D E O
V
S I G N A L
I D
1
V
I D
2
V
S
I D
-
V
S
I D E O
-
V
L
I
d
p
r
a
a
o
i n
n
u t
i
t i o n s
e
e
V
B u t t o n o n t h
e
R
m
o t
T V
e
e
I D
1
V
L I N E
I D
V
I D E O
V
S
I D
-
V
I N
P U
T
R
S O
E
U
C
A
X
U
C
a
l #
h
n n
e
0 0
9 0
9 1
9 2
I D
1
V
I D
2
V
Chapter 5
Advertisement
Table of Contents
