Table of Contents
Advertisement
Quick Links
INSTALLATION AND OPERATING INSTRUCTIONS
ANCHOR WINCH
T10219-AD Deckboat 40™
with AutoDeploy and Wireless Remote Control
If you have any questions or difficulty
installing this product, we are here to help!
First READ THIS MANUAL.
If you still need help, call us from 9 am to 4 pm
(Central time) Monday – Friday.
(615) 462-6224
Note: At this time, we provide Phone Support in English only.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for TRAC Deckboat 40 T10219-AD
Summary of Contents for TRAC Deckboat 40 T10219-AD
- Page 1 INSTALLATION AND OPERATING INSTRUCTIONS ANCHOR WINCH T10219-AD Deckboat 40™ with AutoDeploy and Wireless Remote Control If you have any questions or difficulty installing this product, we are here to help! First READ THIS MANUAL. If you still need help, call us from 9 am to 4 pm (Central time) Monday –...
- Page 2 Installation and Operating Instructions Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain this anchor winch. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.
- Page 3 Anchoring hazards. It is a best practice to tie the anchor line off to a cleat (or other secure point) when the boat is anchored. The winch life may be reduced if it is used to hold the load of the boat while anchored. Damage to the winch motor WILL occur if you motor your boat while the anchor is down (dragging the anchor will damage the winch).
- Page 4 To expose the winch frame mounting holes, remove the four Phillips head screws that hold the plastic cover on the winch frame, and disconnect the white switch connector. Lay cover aside in a safe location. Mark and drill 3 (or 4) bolt holes. Locate the end of the winch frame where there are two slots. A bolt is required in these two slots.
- Page 5 Disconnect anchor winch positive wire from battery. Press and hold the UP and DOWN buttons on the winch housing (DO NOT RELEASE UNTIL STEP 7) Connect the battery positive wire. Press and hold any button on the remote for one second and release. Disconnect battery positive wire.
- Page 6 This limited warranty is not transferable to any other party. TRAC will at it option repair or replace any part(s) of the TRAC Anchor Winch which may be found by TRAC to be defective within two (2) years of purchase. TRAC will pay the shipping charge to the purchaser for any part(s) which may be shipped by TRAC.
- Page 7 TRAC Outdoor Products Company 251A Mayfield Drive Smyrna, TN 37167 www.trac-outdoor.com info@trac-outdoor.com 615/462-6224...
Need help?
Do you have a question about the Deckboat 40 T10219-AD and is the answer not in the manual?
Questions and answers
if wires are not long enough. what gage wire would you recomend?
The recommended wire gauge for the TRAC Deckboat 40 T10219-AD is a minimum of 14 AWG with a 105°C temperature rating. Using a smaller gauge wire could result in overloading and a fire. Larger gauge wire is permitted.
This answer is automatically generated
I just purchased and installed trac 40 deckboat witch. It works fine using the controls on the motor but the remoted does not work. Its like it is not getting any power. Do you have any suggests for me.
If the remote for the TRAC Deckboat 40 T10219-AD is not receiving power, possible issues include:
1. Battery Disconnection – Ensure the anchor winch's positive wire is properly connected to the battery.
2. Remote Battery Issues – Check if the remote control has a functioning battery. Replace if necessary.
3. Distance Limitation – Ensure the remote is within the 50-foot operational range.
4. Interference or Signal Issue – If the remote was reset or lost programming, reprogram it following the manual's instructions.
5. Winch Power Issue – Confirm that the winch itself is receiving power and functioning correctly.
If issues persist, further troubleshooting or support may be required.
This answer is automatically generated