Southwire SIMpull CGS-01 Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Southwire Manuals
  4. Cable Box
  5. SIMpull CGS-01
  6. Operating instructions manual
Southwire SIMpull CGS-01 Operating Instructions Manual

Southwire SIMpull CGS-01 Operating Instructions Manual

Cable guide system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SIMpull CGS-01 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Southwire SIMpull CGS-01

  • Page 2: Table Of Contents

    SAFETY Safety is essential in the use and maintenance of Southwire Contractor Tools and Equipment. This instruction manual and any markings on the tool provide information for avoiding hazards and unsafe practices related to the use of this tool.

  • Page 3: Safety

    SAFETY ALERT SYMBOLS SAFETY ALERT Read and understand all of the instructions and safety information in this manual before operating SYMBOLS or servicing this tool. Failure to observe this warning could result in These symbols are used to call attention to related severe injury or death.

  • Page 4: Important Safety Information

    IMPORTANT SAFETY INFORMATION WARNING Potential Electrical Shock Hazard: The CGS is not a power tool but is made entirely of conductive steel tubing, tubing connectors and roller guide components. Use caution when working around energized electrical equipment. Never use inside of electrical equipment that is energized. IDENTIFY PARTS/COMPONENTS - Extension tubes (Model # CGS-10) - Tube Extender w/ 90 Degree Joint (Model # CGS-12)

  • Page 5: Set-Up And Operation

    SET UP AND OPERATION The following is a guide that if followed should result in an efficient and easy set up. Some jobsite conditions or obstructions may require a slightly different sequence. 1. Select the correct adapter for type of feed. UP FEED 2A.
  • Page 6 SET UP AND OPERATION cont. DOWN FEED 3A. Select the down feed roller assembly (Fig. 5) and appropriate size of conduit adaptor. Secure the conduit adaptor into the roller assembly by pulling pin and sliding adaptor into place (Fig. 6A). Release pin to ensure conduit adaptor is place.
  • Page 7 SET UP AND OPERATION cont. ASSEMBLY cont. 5. Attach each section using either the tube extender joints (Fig. 9A and Fig. 9B) or a Universal Joint Assembly (Fig. 10A and Fig. B). Connectors are secured with pull pins and tube extenders are secured by tightening the knobs attached. There should be a joint or tube extender between each section of tubing.
  • Page 8 SET UP AND OPERATION cont. ASSEMBLY cont. 6. While working your way back from the conduit, adjustments may be required along the way to accommodate for bends and turns along desired path. You can now set the angle of the locking universal joint assembly by turning center 3/8” Allen bolt counter-clockwise (Fig.
  • Page 9 SET UP AND OPERATION cont. ASSEMBLY cont. 8. Lastly secure the last tubing section to the reel adaptor assembly by aligning extension tube (Fig. 16) and inserting supplied pin (Fig. 17). Fig. 16 Fig. 17 9. If mounting to the Maxis ®...
  • Page 10 SET UP AND OPERATION cont. ASSEMBLY cont. 10. Place the roller guides at 4 to 5 foot spacing or two guides per section. Adjust spacing as required. The size/number of wires, degree of change in direction and elevation will dictate placement and the actual number of guides needed. Once located, swing bottom metal tab 180 degrees out from its locked position and place on tubing (Fig.

  • Page 11: Maintenance

    MAINTENANCE As with any tool the cleaner it is kept and maintained the better it will perform. Wipe down all parts after use to ensure optimal performance. Ensure lubrication of all moving is maintained to ensure smooth operation. SPECIFICATIONS • Model # CGS-01 •...

  • Page 12: Warranty

    Under Southwire’s Contractor Equipment 5-Year Limited Warranty, Southwire Company, LLC warrants that all Southwire Contractor Equipment will be free from manufacturer defects for a period of five (5) years from the date of the original end user’s purchase. The following products are excluded from this 5-Year Limited Warranty and are subject to separate warranty terms: rope, blades, dies, draw studs, grips, Southwire Contractor Equipment electronic components, and Material Boxes.
  • Page 13 1. All warranty claims must be approved by Southwire’s Tools & Assembled Products Warranty Department prior to return of product. If Southwire determines that a product is defective, Southwire will, at its option, repair or replace defective products or defective product components, free of charge.

This manual is also suitable for:

25968137

Table of Contents