Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for NBE RTB Tokyo
- Page 1 TRÆPILLESYSTEM RTB - ready to burn Wood Pellet Grill...
-
Page 2: Table Of Contents
Dear Customer, Thank you for purchasing this NBE product which is designed and manufactured in Denmark according to the highest standards in the EU. In order for you to get the most out of your TRÆPILLESYSTEM product, we strongly recommend that you carefully read this manual prior to operating the grill. - Page 3 WARNINGS IMPORTANT SAFETY INFORMATION! PLEASE READ ALL PRIOR TO INSTALLATION AND USE DANGER, WARNING and CAUTION are used throughout this manual for marking particularly important information and instructions. Read and follow these instructions to avoid injury to yourself, others, or the equipment. The signal words are defined below: DANGER: Marks a hazardous situation where if not taken into account, could result in death or serious injury.
- Page 4 WARNINGS WARNING: Do not move the grill when in use. WARNING: Keep electrical wires away from hot surfaces. Follow the instructions for wiring. WARNING: Place the power cord away from busy areas. Make sure the wire is placed so you do not risk pulling it or stumbling over it.
-
Page 5: Technical Data
TECHNICAL DATA: GRILL Temperature Temperature Temperature sensor zone 3 sensor zone 1 sensor zone 2 Burner adjustment rod- allows you to 15 kg adjust the hopper temperature in the three heating zones. Controller serial number and Hook for grease password for the basket. -
Page 6: Assembly
ASSEMBLY T25 bit T25 bit Required tools: • 1 x grill • 1 x top rack assembly • 1 x burner • 11 x T25 head w/ 10mm screws adjustment (for side table and chimney) • 1 x burner • 1 x Grill deflection scraper plate... - Page 7 ASSEMBLY Thread the adjustment rod through the side Install the top and bottom level grill opening of the grill and ensure that the grates burner head is resting securely above the burner. Ensure that the burner deflection plate is Attach the side table and chimney pipe securely lowered on the attachment brackets with the accompanying screws (T25).
-
Page 8: Operating The Burner Adjustment Rod
OPERATING THE BURNER ADJUSTMENT ROD: Heating Zone Control The RTB grill has three temperature zones that can be adjusted manually by adjusting the burner’s re-directional head in 5 possible notched positions which include 2, 1, 0, 1 & 2 respectively from left to right. Note: The burner on the grill will modulate to maintain the wanted grill temperature based on the highest temperature value measured among the three zone temperature sensors. - Page 9 FIRST TIME START UP (with control panel) Use UP and DOWN arrows to set the desired grill temperature. Button to change between °C to °F The three center screens displays the temperature of the left, center, and right heating zones of the grill. Alarm deactivate Use UP and button.
- Page 10 FIRST TIME START UP (with control panel) 5. Ensure that the two provided grease buckets are attached on the two opposite hooks found inside the bottom cabinet. 6. Press the On button to Start. WARNING: During first start-up it is important to allow for a minimum of 1 hr of running to allow for any oil on the metal to burn off of the grill prior to placing any food on the grate.
-
Page 11: Connecting Via An Android Device
CONNECTING VIA ANDROID DEVICE Find the controller number Make sure there is power on Search “NBE BBQ” in Google and password on the inside of the the grill. Have your device in close Play and install app cabinet door proximity to the grill and select “START”... -
Page 12: Connecting Via An Iphone
CONNECTING VIA IPHONE Search “NBE BBQ” in App Connect power to the grill Find the grill’s controller and go to SETTINGS/WIFI and Store and install app. number and password on the connect to BBQXXXXX. inside of the cabinet door Select USE BARBECUE WITH LOCAL... -
Page 13: Modes Of Operation
MODES OF OPERATION (Requires App) The RTB grill app will allow for some additional operational modes and settings that are not found on the grill’s control panel itself. In general, there are four modes of operation which include: • Temperature Regulation Mode •... - Page 14 MODES OF OPERATION (Requires App) priority: Fixed Power Mode will operate when: • A Fixed Power % between 10-100% power is selected • Smoke Timer is not active • And Internal Meat Temperature is not reached 4th priority: Temperature Regulation Mode will operate when : •...
-
Page 15: Example Settings
EXAMPLE SETTINGS EXAMPLE- FIXED EXAMPLE-SMOKE POWER MODE MODE SETTINGS Low Temperature Fixed Power Mode will Smoking mode will operate when: operate if : • A Fixed Power % • A Smoke Step level 1-5 between 10-100% is chosen power is selected •... -
Page 16: App Settings
APP SETTINGS HOME SETTINGS On/OFF/Reset Alarm Pellet Feed Min Power Grill Temp 1, 2, & 3 Pellet Feed Max Power Meat Temp sensor 1 Fan Speed Min Power & 2 Fan Speed Max Power Grill Temp (40- 300° C) Pellet Feed- Smoking Meat Temp Sensor 1 Fan Speed- Smoking Meat Temp Sensor 2... - Page 17 APP SETTINGS Temperature Regulation Mode Settings: • Grill Temperature- desired temperature of the grill between 40 – 300°C • Pellet Feed Min Power- the % of pellet feeding when the grill is performing at minimum power 10%. • Pellet Feed Max Power- the % of pellet feeding when the grill is performing at maximum power 100%.
- Page 18 APP SETTINGS Fixed Power Mode Settings: • Fixed Power %- the Fixed Power % the grill should run during FIXED POWER MODE. Fixed Power % is ideal during open air grilling, when you expect to frequently open and close the grill top lid, or if you prefer to manually control the grill temperature via the fixed power % of the burner.
- Page 19 MAINTENANCE: GRILL Temperature Temperature Temperature sensor zone 3 sensor zone 1 sensor zone 2 Burner adjustment rod- allows you to 15 kg adjust the hopper temperature in the three heating zones. Controller serial Hook for grease number and basket. Always password for the ensure that the grill app is found...
-
Page 20: Electrical Scheme
ELECTRICAL SCHEME: Screen Connector INPUT OUTPUT FUNCTION Cable color 110-240V PE-N-L 110-240 Volt AC PE= Green/Yellow, N= Blue, L= Brown PE= Green/Yellow, N= Black, L= White OUTPUT (1) PE-N-L1 Auger (with Cap), Red (with Cap) OUTPUT (2) PE-N-L2 N= Black, L2=Black N=White, L3= White (110V) / OUTPUT (3) PE-N-L3... -
Page 21: Replacement Parts
REPLACEMENT PARTS: Use only genuine NBE replacement parts. Contact your local NBE authorized dealer for replacement parts for your RTB grill. - Page 22 DECLARATION OF CONFORMITY...
-
Page 23: Troubleshooting:alarms
TROUBLESHOOTING:ALARMS ERROR CODE ERROR NAME ERROR DEXCRIPTION ERROR LIGHT No light value (LUX) is recognized after an ignition SENSOR cycle. Check that the igniter functions in Manual Control. Check that the burner grate is clean prior to starting the grill. An unclean burner grate with blocked holes can prevent the photosensor from recognizing a completed ignition.