U.S.SAWS Metabo WEV15-125 Quick HT Operating Manual page 5

4.15 SHUT OFF MACHINE.
When not in use, before servicing and when changing accesso-
ries, shut off engine. Release the lever switch and move the on/
off switch to the OFF position. Move the fuel valve lever to the OFF
position.
4.16 STORE IDLE EQUIPMENT.
The machine and tools should be stored in a dry and secure loca-
tion when not in use. Keep equipment out of reach of children.
4.17 OBTAIN SAFETY DATA SHEET (SDS) FOR ALL
WORKSURFACE MATERIALS.
This includes primers, all coatings, adhesives, tile and crack filling materials, etc.
Do not attempt to cut, clean out or remove material without SDS information. Con-
sult SDS sheet for hazards information. Be aware that some materials are explosive
as a dust.
4.18 DO NOT OVERREACH.
Keep proper footing and balance at all times.
4.19 MAINTAIN MACHINE WITH CARE.
Keep machine clean and follow maintenance procedures for better and safer
performance. Keep handles dry, clean, and free from oil and grease. Follow instruc-
tions for lubricating and changing accessories.
4.20 REMOVE ADJUSTING TOOLS.
Form a habit of checking to see that tools such as adjusting wrenches are
removed from the machine and properly stored before starting the engine.
4.21 STAY ALERT.
Watch what you are doing. Use common sense. Do not operate machine
when you are tired or fatigued.
4.22 DO NOT USE DRUGS, ALCOHOL, MEDICATION.
Do not operate machine while under the influence of drugs, alco-
hol,
or any medication.
4.23 KEEP THE RIGHT PARTS IN THE RIGHT POSITIONS.
Do not operate machine with parts missing or improperly mounted.
4.24 CHECK DAMAGED PARTS.
Verify all machine guards are in good condition and will function
properly before using the machine. Check for alignment of moving
parts, binding of moving parts, breakage of parts, mounting, and
any other conditions that may affect machine operation. A guard,
power switch or other part that is damaged should be properly re-
paired or replaced by an authorized service center unless indicat-
ed elsewhere in this instruction manual. Do not operate machine if
lever or engine on/off switch does not function properly.
4.25 SECURELY MOUNT ACCESSORIES TO THE MACHINE.
Extra care must be taken an elevated location to prevent injury to
someone on a lower level in the event the tool or accessory should
drop. Do not operate without fall protection for operator and debris
protection for public.
S A F E T Y I N S T R U C T I O N S
Surface Prep
Division
4.26 NEVER TOUCH THE MOVING PARTS.
Never touch moving parts such as blades, belts and others.
4.27 STOP OPERATION IMMEDIATELY IF ANY ABNORMALITY
IS DETECTED.
Stop using machine immediately if any abnormalities are observed
during operation. Examples of abnormalities include unusual noise
and vibration.
4.28 WHEN REPLACING A PART, USE THE SAME TYPE
AND QUALITY.
When replacing a component part with a new one, use only the
same type and quality of new part. Never attempt to repair a ma-
chine if you are unfamiliar with proper procedures and techniques
required.
4.29 LOAD AND UNLOAD SAFELY.
Use proper heavy lifting procedures. Read & understand manuals
before loading & unloading.
4.30 SAVE THESE INSTRUCTIONS.
Refer to this operations and maintenance manual as well as any
additional instructions included from other manufacturers and
organizations such as Metabo® and the Masonry and Concrete
Saw Manufacturers Institute®. Never permit anyone to operate the
machine without proper instructions.
DUST WARNING
Cutting, especially when DRY cutting, generates dust that comes
from the material being cut, which frequently contains silica.
Silica is a basic component of sand, quartz, brick clay, granite and
numerous other minerals and rocks. Exposure to excessive amount of
such dust can cause:
• Respiratory diseases (affecting your ability to breath), including
chronic bronchitis, silicosis and pulmonary fibrosis from exposure
to silica. These diseases may be fatal;
• Skin irritation and rash; and
• Cancer according to NTP* and IARC*
* National Toxicology Program, International Agency for Research
on Cancer
Take precautionary steps
• Avoid inhalation of and skin contact with dust, mist and fumes;
• Wet cut when feasible, to minimize dust;
• Wear and ensure that all bystanders wear appropriate respiratory
protection such as dust masks designed to filter out microscopic
particles. (See OSHA 29 CFR Part 1910.1200)
California Prop 65 Warning: Use of this product can cause exposure to
materials known to the State of California to cause cancer and/or birth
defects or other reproductive harm.
P: 877-817- 6687 F: 813-621-7125
Visit us at www.ussaws.com
sales@ussaws.com
5