Sony MDR-EX33LP Operating Instructions

Stereo Headphones
Operating Instructions
Manual de instrucciones
MDR-EX33LP
©2008 Sony Corporation Printed in Thailand
A
L-shaped stereo
mini plug
1.2 m
Cord adjuster
1
2
B
Sectional View
1
2
3
C
4-111-691-21(1)
3
Colored parts
English
Features
• SS (small & short) size earbuds supplied for smaller ears
• Hybrid silicone rubber earbuds for secure fit and long-term wearing comfort
• Convenient cord adjuster supplied
Wearing the headphones (see fig. A)
Wear the earpiece marked R in your right ear and the one marked L in your left ear.
There is a tactile dot on the unit marked L to distinguish the left side.
How to use the supplied cord adjuster
You can adjust the cord length by winding the cord (1) on the cord adjuster and then push the
cord into the slot hole to secure in place (2).
(The cord can be wound to the cord adjuster up to 50 cm. If you wind more, the cord comes off
from the cord adjuster easily.)
Note
Do not wind the plug or split section of the cord, as it will strain the cord and may cause a wire
break.
How to use the cord slider (3)
Move up and down to change the split position of the cord.
How to install the earbuds correctly
If the earbuds do not fit your ears correctly, low-bass sound may not be heard. To enjoy better
sound quality, change the earbuds to another size, or adjust the earbuds position to sit on your
ears comfortably and fit your ears snugly.
If the earbuds do not fit your ears, try another size. Confirm the size of the earbuds by checking
the color inside (see fig. B–1).
When you change the earbuds, install them firmly on the headphones to prevent the earbud
from detaching and remaining in your ear.
Earbud sizes (inside color)
Small
>
SS S M
(Red) (Orange) (Green)
* This size is optional and available at purchase.
To detach an earbud (see fig. B–2)
While holding the headphone, twist and pull the earbud off.
To attach an earbud (see fig. B–3)
Push the parts inside of the earbud into the headphone until the projecting part of the headphone
is fully covered.
Cleaning the earbuds
Remove the earbuds from the headphones, and wash them with a mild detergent solution.
Specifications
Type:
Closed, dynamic
Driver unit:
9 mm, dome type (CCAW)
Power handling capacity: 100 mW (IEC*)
16 Ω at 1 kHz
Impedance:
Sensitivity: 100 dB/mW
Frequency response: 6 – 23,000 Hz
Cord: 1.2 m (47
Plug: Gold-plated L-shaped stereo mini plug
Mass: Approx. 3 g (0.11 oz.)
Supplied accessories
Earbuds (SS × 2, S × 2, M × 2)
Cord adjuster (1)
* IEC = International Electrotechnical Commission
Design and specifications are subject to change without notice.
Precautions
• Please keep your headphones clean at all times especially inside the rubber earbud. (see fig. C)
If any dust or ear wax inside the earbud, you may experience some listening difficulties.
• During dry weather, you may experience mild pain in your ears. This is not by malfunction of the
headphones, but is due to static electricity accumulated in your body. It is reduced by wearing
clothes made of natural materials that do not generate static electricity so easily.
• Listening with headphones at high volume may affect your hearing. For traffic safety, do not use
while driving or cycling.
• The earbuds may deteriorate due to long-term storage or use.
• Install the earbuds firmly onto the headphones. If an earbud accidentally detaches and is left in your
ear, it may cause injury.
EP-EX10A is available (sold separately) as optional replacement earbuds.
EP-EX10A offers 4 types of the earbuds: SS, S, M and L.
Large
.
L*
(Light blue)
1 / in.), Litz cord Y-type
4