Directed 3305 Installation Manual
  1. Manuals
  2. Brands
  3. Directed Manuals
  4. Power Supply
  5. 3305
  6. Installation manual
Directed 3305 Installation Manual

Directed 3305 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

3305 & 3105
Installation Guide
This product is intended for installation by a professional installer
only! Any attempt to install this product by any person other than
a trained professional may result in severe damage to a vehicle's
electrical system and components.
N3X05 2019-03

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 3305 and is the answer not in the manual?

Questions and answers

Summary of Contents for Directed 3305

  • Page 1 3305 & 3105 Installation Guide This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.
  • Page 3 XKLOADER3, Code Hopping™, DEI®, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn Routine™, Nuisance Prevention® Circuitry, NPC®, Revenger®, Silent Mode™, Soft Chirp®, Stinger®, Valet®, VRS®, and Warn Away® are all Trademarks or Registered Trademarks of Directed. © 2019 Directed. All rights reserved.
  • Page 4 Read the Government regulations section of this manual prior to operating this system. Warning! Failure to heed this information can result in injury, damage or the illegal use of the system beyond its intended purpose. © 2019 Directed. All rights reserved.

  • Page 5: Table Of Contents

    Primary Harness - 12-pin connector ..............4 Door Lock Harness, White 3-pin connector ............9 Control Center ....................9 XKLOADER3/Directed SmartStart, Black 3-pin connector ........10 Mounting the Control Center ................11 Onboard Dual Stage Shock Sensor ..............12 Optional Sensor Harness, White 4-pin connector ..........12 Parking Light Jumper ..................13...

  • Page 6: Wiring Diagram

    Wiring Diagram © 2019 Directed. All rights reserved.

  • Page 7: Wiring Connections

    Important: Never use this wire to drive anything but a relay or a low-current input! The transistorized output can only supply 200 mA of current. Con- necting directly to a solenoid, motor, or other high-current device will cause it to fail. © 2019 Directed. All rights reserved.

  • Page 8: Primary Harness - 12-Pin Connector

    1-amp diode must be installed to ensure proper operation. Insert the diode as shown in the following diagram. Important: Never interrupt any wire other than the starter wire. © 2019 Directed. All rights reserved.
  • Page 9 This wire provides a (-) 200 mA output, whenever the remote control button(s) controlling channel 3 output is pressed. This wire can be pro- grammed to provide different types of outputs (see "System features learn routine" on page 14 of this guide). © 2019 Directed. All rights reserved.
  • Page 10 GREEN (-) DOOR TRIGGER INPUT Most vehicles use negative door trigger circuits. Connect the Green wire to a wire showing ground when any door is opened. When con- © 2019 Directed. All rights reserved.
  • Page 11 This input will respond to a negative input with an instant trigger. It is ideal for hood and trunk pins and will report on Zone 1. It can also be used with Directed single-stage sensors. The Blue instant trigger wire can also be used to shunt sensors during operation of auxiliary channels or remote start.
  • Page 12 Important: Never use this wire to drive anything but a relay or a low-current in- put! The transistorized output can only supply 200 mA of current. Connecting directly to a solenoid, motor, or other high-current device will cause it to fail. © 2019 Directed. All rights reserved.

  • Page 13: Door Lock Harness, White 3-Pin Connector

    Control Center The LED and the valet switch are incorporated into the Control Center. The control center plugs into the 6-pin port on the module with black RF cable provided. Valet switch Control Center © 2019 Directed. All rights reserved.

  • Page 14: Xkloader3/Directed Smartstart, Black 3-Pin Connector

    XKLOADER3/Directed SmartStart, Black 3-pin connector The Black 3-pin port connection is for programming the unit or when using the optional Directed SmartStart module. When using the XKLoader3 Bitwriter PRG1000 XKLoader2 XKLOADER3 and Directechs mobile app, it is possible to configure any and all of the programmable functions.

  • Page 15: Mounting The Control Center

    Antenna receiver cable Important: To achieve the best possible range, DO NOT leave the antenna cable bundled under the dash. Always extend the cable full length during installation, regardless of the antenna mounting location. © 2019 Directed. All rights reserved.

  • Page 16: Onboard Dual Stage Shock Sensor

    The power and ground outputs of this plug cannot support Important: high current sensors such as a 508D. Power and ground for the sen- sor should be connected to the red and black wire of the primary 12-pin harness connection. © 2019 Directed. All rights reserved.

  • Page 17: Parking Light Jumper

    Important: DO NOT connect the parking light wire of the primary 12-pin harness to a negative vehicle parking light wire before changing the pro- gramming jumper to the negative polarity position or damage to vehicle light circuit may occur. © 2019 Directed. All rights reserved.

  • Page 18: Bypassing Sensor Inputs

    Blue Instant Trigger Input wire of the primary 12-pin harness without triggering the unit. This can be done using the status and ignition output of a Directed remote engine starting unit, as described in the following diagram:...
  • Page 19 HOLD it. The siren will chirp the number of times equal to the step you have accessed. Program the Feature. While holding the Control Center button, you can program the feature using the remote control. Pressing © 2019 Directed. All rights reserved.
  • Page 20 After three seconds, the unit advances to the next menu, the siren chirps and LED flashes indicating which menu has been accessed. The Learn Routine exits if any of the following occurs: • Close the open door. • Ignition is turned On © 2019 Directed. All rights reserved.

  • Page 21: Feature Menus

    3 chirps: 0.4 sec Forced passive arming ON Forced passive arming OFF Automatic Engine Disable ON Automatic Engine Disable OFF Armed When Driving (AWD) Vehicle Recovery System (VRS) 1-10 Code Hopping ON Code Hopping OFF © 2019 Directed. All rights reserved.

  • Page 22: Menu 2

    Channel 3: latched/ latched reset with ignition/ 30- second timed/Factory Alarm Disarm (FAD)/Factory Alarm Trigger (FAT) / second unlock output 2-11 Comfort Closure (ON, 20 sec) Comfort Closure (OFF) XKLOADER3 allows programming from 1-180 seconds. © 2019 Directed. All rights reserved.

  • Page 23: Feature Descriptions

    With Active Locking the doors do not lock when the system is pas- sively armed. When Passive Arming is selected, the system chirps 20 seconds after the last door is closed. Arming the system or locking the doors occurs 30 seconds, after the door closes. © 2019 Directed. All rights reserved.
  • Page 24 (Armed While Driving), the system can be armed with the ignition on. When armed, the ground-when-armed is not active and the sensors are bypassed. The door triggers remain active. If programmed to the VRS (Vehicle Recovery System) setting, VRS is activated. © 2019 Directed. All rights reserved.

  • Page 25: Menu 2

    During that hour if a trigger occurs on the same zone again, the system resets the one hour timer. If after an hour the sensor has not triggered © 2019 Directed. All rights reserved.
  • Page 26 2-7 Ignition-Controlled Domelight Supervision ON/OFF: If turned ON, domelight illuminates for 30 seconds when the ignition is turned OFF. Domelight Supervision is an optional feature and may required additional parts and labor. © 2019 Directed. All rights reserved.
  • Page 27 Latch/Reset with Ignition: When the command for Channel 3 is received, the system will output a (-) and will remain on until the command from the remote is received again or the © 2019 Directed. All rights reserved.
  • Page 28 800ms after the door lock output pulses (or 2nd pulse for double pulses) - the output turns on again for 20 seconds. The Comfort Closure output will be cancelled if the button is pressed. DRW-226 © 2019 Directed. All rights reserved.

  • Page 29: Pairing A Remote Control

    LED blinks the number of times corresponding to the channel accessed. Channel/ Function Channel Function Wire Color Arm/Disarm Panic Only Silent mode, Remote Valet, Red/White Trunk Release Remote starter or other accessories White/Blue © 2019 Directed. All rights reserved.
  • Page 30 This is useful when a customer’s remote is lost or stolen. All remote controls are erased from the system’s memory. You can also start from scratch, if the remote buttons are programmed incorrectly. © 2019 Directed. All rights reserved.
  • Page 31 Ignition is turned off. • Door is closed. • Control Center button is pressed too many times. • More than 15 seconds elapse between steps. One long chirp indicates that the Learn Routine has been exited. © 2019 Directed. All rights reserved.

  • Page 32: Remote Control Configurations

    DRW-226 DRW-226 Panic Channel 3 3-button configuration (optional, not included) DRW-226 Arm/Disarm DRW-226 Channel 2/Silent Mode Panic DRW-226 DRW-226 Note : Multi Level Security Arming feature is not available with the 3-button remote control. © 2019 Directed. All rights reserved.

  • Page 33: Diagnostics

    For information on which zone is active or has been violated refer to the Table of Zones. Status Chirps Action Chirps System status Armed Armed with bypass notification Disarm Disarmed Disarmed with tamper alert Disarmed/NPC active © 2019 Directed. All rights reserved.

  • Page 34: Table Of Zones

    Warn Away response, while inputs longer than 0.8 seconds will instantly trigger a full alarm sequence. Two-staged Ignition input. Yellow wire of the primary 12- pin harness. Note: The Warn Away response does not report on the LED. © 2019 Directed. All rights reserved.

  • Page 35: Multi-Level Security Arming

    For a full de- scription of Multi-Level Security Arming operation for testing purposes refer to the Owner’s Guide. Note: This feature is not available with the optional three-button remote control. © 2019 Directed. All rights reserved.

  • Page 36: Vrs (Vehicle Recovery System)

    Rapid Resume Logic ensures that when the system is powered up it returns to the same state it was in before power was disconnected. For a full description of Rapid Resume Logic refer to the Owner’s Guide. © 2019 Directed. All rights reserved.

  • Page 37: Troubleshooting: Security

    Are the door inputs connected? Is a Blue wire connected to the door trigger wire in the vehicle? Either the Green or the Violet wire of the primary 12-pin harness should be used instead. © 2019 Directed. All rights reserved.
  • Page 38 "Feature Descriptions" on page 19 of this guide.) The Control Center button doesn’t work or LED doesn't work. • Make the connector is securely plugged in to the alarm module and Control Center. © 2019 Directed. All rights reserved.

  • Page 39: Government Regulations

    RF exposure compliance. This device is designed to be used in a person’s hands and its operating configurations do not support normal transmissions while it is carried in pockets or holsters next to a person’s body. © 2019 Directed. All rights reserved.
  • Page 40 WARNING! Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device © 2019 Directed. All rights reserved.
  • Page 42 The company behind this system is Directed Since its inception, Directed has had one purpose, to provide consumers with the finest vehicle security and accessories available. The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology.

This manual is also suitable for:

3105

Table of Contents