Related Manuals for NU CT424
Summary of Contents for NU CT424
- Page 1 Operator's Manual Edging Power Trowel CT424 & CT430 Unit 2 Low Farm Low Road, Morley St Botolph, Wymondham, United Kingdom, NR18 9BU sales@nuequipment.co.uk 01953 711952 www.nuequipment.co.uk...
- Page 2 Original instructions This Operator’s Manual presents the original instructions. The original language of the Operator’s Manual is English.
- Page 3 Foreword This manual contains important instructions for this machine. These instructions must be followed during installation, operation, and maintenance of the machines. This manual provides information and procedures to safely operate. For your own safety and to reduce the risk of injury, carefully read, understand, and observe all instructions described in this manual.
-
Page 4: Table Of Contents
Table of Contents Foreword Warranty 1. SAFETY INFORMATION. ………………………………………………………………….. .5 1.1 Operating Safety…………………………………………………………………………..5 1.2 Operator Safety while using Internal Combustion Engines……………………………..6 1.3 Label Locations………………………………………………………………………………6 1.4 Safety and Operating Labels……………………………….…………………………….7-8 2. OPERATION …………………………………………………………….……………………... 9 ….. 2.1 Operating Principle…………………………………………………………………………… 2.2 Application – Standard Feature………………………………………………………………… 2.3 Delivery Checks ……………………………………………………………………….…………... -
Page 5: Safety Information
1. SAFETY INFORMATION 1.1 Operating Safety Only trained personnel are permitted to start, operate, and shut down the machine. They have received instruction on how to properly use the machine and are familiar with required safety devices The machine must not be accessed or operated by children and people impaired by ... -
Page 6: Operator Safety While Using Internal Combustion Engines
1.2 Operator Safety while using Internal Combustion Engines DO NOT smoke when refueling the engine or during any other fuel handling operation. DO NOT refuel a hot or running engine. DO NOT refuel the engine near an open flame. ... -
Page 7: Label Locations
1.3 Label Location... -
Page 8: Safety And Operating Labels
Safety and Operating Labels Our machines use international pictorial labels where needed. These labels are described below: Label Meaning DANGER! Engines emit carbon monoxide; operate only in well-ventilated area. Read the Operation Manual for machine information. No sparks, flames, or burning objects near the machine. - Page 9 Label Meaning WARNING! Hand injury if caught in moving belt. Always replace belt guard. CAUTION! Lifting point. CAUTION! Use only clean, filtered fuel. WARNING! Hot surface! A nameplate listing the model number and serial number is attached to each unit. Please record the information found on this plate so it will be available if the nameplate lost or damaged.
-
Page 10: Operation
2. OPERATION 2.1 Operating Principle The following instructions were compiled to provide you information on how to obtain long and trouble free use of the machine. Periodic maintenance of the machine is essential. Read the manual carefully and thoroughly familiarize yourself with the machine and all it’s functions. -
Page 11: Unfolding The Handle
2.4 Unfolding the Handle To unfold and secure the handle assembly: 1. New machine with folded handle. 2. Unfolding the adjustable handle and lock the screw. 3. Straighten the handle and lock the hinge pin. 4. Tighten the adjustable lever to lock the handle in its fully opened position. 2.5 Before Starting Before starting the machine, check the following items: All handles are free from grease, oil and dirt. -
Page 12: To Start
2.6 To Start Before starting the machine must know the location and function of all controls. Make sure the safety stop switch is in the stop position. If it is not, push the lever down to the stop position before attempting to start the engine. Open fuel valve under fuel tank (if so equipped), open throttle approximately half way down and apply choke. -
Page 13: Maitenance
3 MAINTENANCE 3.1 Periodic Maintenance Schedule The chart below lists basic trowel and engine maintenance. Refer to engine manufacturer’s Operator's Manual for additional information on engine maintenance. A copy of the engine Operator's Manual was supplied with the machine when it was shipped. To service the engine, tilt the seat forward. -
Page 14: Lubrication
3.2 Lubrication The long life and successful operation of any parts of machinery is dependent on frequent and thorough lubrication. Before using the machine, always check the oil and use proper oil with the correct type and grade as recommended. NOTICE: DO NOT mix types of oil in gearbox and DO NOT overfill the oil. -
Page 15: Trouble Shooting
3.4 Trouble Shooting SYMPTOM POSSIBLE CAUSES SOLUTION Engine running rough Safety switch malfunction? Make sure that the safety switch or not at all. is ON or replace switch if necessary. Fuel? Look at the fuel system. Make sure there is fuel being supplied to the engine. - Page 16 Thrust collar bushing? Check the thrust collar by rocking it on the spider. If it can tilt more than 3/32" (2.4mm) [as measured at the thrust collar O.D.], replace the bushing in the thrust collar. Thrust bearing worn? Check the thrust bearing to see that it is spinning free.
-
Page 17: Technical Data
70-150 Rotor Dia. cm(in) 79(30) Combination Blade 6 x 10.5 Float Pan Gearbox Lubrication type/ml Engine type may vary, please see listing Working Size (L x W x H): Model L (mm) W(mm) H(mm) CT424 Series 1560 CT430 Series 1560... -
Page 18: Sound Specification
The weighted effective acceleration value, determined according to ISO 2361-1 and ISO 5349, is: for hand arm: CT424 Series: 1.1 m/s CT430 Series: 1.3 m/s The sound and vibration specifications were obtained with the unit operating on fully cured, water... - Page 19 Unit 2 Low Farm Low Road, Morley St Botolph, Wymondham, United Kingdom, NR18 9BU sales@nuequipment.co.uk 01953 711952 www.nuequipment.co.uk Version: 201312-02...