Worx WX082L, WX082L.X - Cutter Manual

NOTE: Before using the tool, read the instruction book carefully.

ASSEMBLY

REMOVING AND INSTALLING THE BLADE (See Fig. A1, A2)

NOTE: When changing the blade, you need to find something to secure the blade (e.g. vise).Then, you must insert an object (such as a small slotted screwdriver) into the Blade screw (5) to lock in place. (See Fig. A1)

1. Rotate blade screw counter clockwise with a slot tip screwdriver and remove the blade screw.
2. Slide the blade away from the upper guard and remove blade.
3. Slide new blade under the upper guard with beveled edges facing you.
4. Align hole in blade with hole in the blade shaft, replace screw and securely tighten the blade screw clockwise.

OPERATION

INTENDED USE

The tool is intended for cutting flexible, soft materials of up to 6 mm in thickness, such as carpet, PVC, cardboard, leather, fabrics and similar materials.

ON / OFF SWITCH

(See Fig. B)

Your switch is locked off to prevent accidental starting. Depress lock off button then on/off switch and release lock off button. Your tool is now on. To switch off just release the on/off switch.

CHARGING THE TOOL

The battery charger supplied matches to the Li-ion battery installed in the machine. Do not use other battery chargers.

The Li-ion battery is protected against deep discharging. When the battery is empty, the machine is switched off by means of a protective circuit: the blade will no longer move.

In a warm environment or after heavy use, the battery pack may become too hot to permit charging. Allow time for the battery to cool down before recharging.

CHARGING

Plug charger plug into a suitable power outlet and afterwards plug your tool into the battery charger. The charging indicator (red) will illuminate at this time.

The charger indicator will turn green when charging is complete. Then unplug the charging plug from the wall socket and then remove the tool from the battery charger.

CUTTING

Thin materials, such as fabrics, can be pulled into the tool during cutting and become wedged. Therefore, do not apply too much pressure with these materials in order to achieve good cutting results. During cutting, apply sufficient tension while holding fabrics and cut slowly.

Do not allow the foot to become wedged during cutting. The foot must be parallel to the cut.

During the charging procedure, the handle of the machine warms up. This is normal.
When not using for extended periods, disconnect the battery charger from the socket.
Do not use the machine during the charging procedure.

MAINTAIN TOOLS WITH CARE

Your power tool requires no additional lubrication or maintenance. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust.

Cleaning

To avoid accidents, always disconnect the tool and/or charger from the power supply before cleaning. The tool may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with compressed air.

When cutting, material residue can accumulate under the upper guard. Remove blade and clean upper guard regularly using a brush or lightly moistened cloth.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through opening.

Certain cleaning agents and solvents damage plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

TROUBLESHOOTING

Problem	Probable cause	Suggested remedy
Blade will not run	Switch in OFF position	Make sure you depress lock off button and on/off switch. Your tool is now on. Release lock off button
	Battery is powered off	Charge your tool with the supplied charger
	Your tool is in charging status	Unplug the charger after charging is completed.
Charging indicator will not illuminate	Connector pin is not plugged in the charger socket completely.	Make sure the connection is good.
	No electrical power at wall outlet	Check circuit breaker or fuse at electrical panel.
Can not remove the blade	The spindle slot (13) is not locked in place	Make sure you insert an object (such as a small slotted screwdriver) into the spindle slot (13) to lock in place. (See Fig. A1)

FOR BATTERY TOOLS
The ambient temperature range for the use and storage of tool and battery is 32°F-113°F (0^oC-45^oC).
The recommended ambient temperature range for the charging system during charging is 32°F-104°F (0 C-40 C).