Reading data from the SD - card and processing in a spreadsheet program Mounting instructions Type Examination Certificate (ATEX) Errors, mistranslation and technical improvement may change these data ! UNDATEC Flow Measurement Solutions Frank Stark - Wiesenstrasse 23 - D-75248 Oelbronn-Duerrn / Germany - Telefon +49 (0) 7237-7804 Email: undatec@web.de...
UNDATEC Flow Measurement Solutions Wiesenstraße 23 75248 Oelbronn-Duerrn - Germany Product Name: FDL400 Flow Data Logger Product Type: Flow measurement for water and wastewater The designated product is in conformity with the following European Council Directives for harmonization of the laws of Member States.
Page 4
About the activities and possible extensions of this manual can be supplied by the company Dömges Detectronic UG. UNDATEC Flow Measurement Solutions Frank Stark - Wiesenstrasse 23 - D-75248 Oelbronn-Duerrn / Germany - Telefon +49 (0) 7237-7804...
- Flow - Totalizer The measuring sensor is powered from the FDL400 device with the necessary voltage. The two values for flow rate and liquid level are directly on the sensor 4-20 mA signal is available. This allows the device to be mounted further away from the location on your channel.
4. FDL400 – Flow Data Logger 4.1 Technical Data The transmitter are housed in an aluminum case and is suitable for wall mounting or DIN rail mounting. The device with connected sensor required after turning a certain time to reach operating temperature (warm-up time).
Page 7
Dimension UNDATEC Flow Measurement Solutions Frank Stark - Wiesenstrasse 23 - D-75248 Oelbronn-Duerrn / Germany - Telefon +49 (0) 7237-7804 Email: undatec@web.de...
Pin Assignment Attention ! In ATEX relevant applications never do operate the sensor without the safety guard via plug ! UNDATEC Flow Measurement Solutions Frank Stark - Wiesenstrasse 23 - D-75248 Oelbronn-Duerrn / Germany - Telefon +49 (0) 7237-7804 Email: undatec@web.de...
This can, for example, come from a connected controller (PLC) or from another source. UNDATEC Flow Measurement Solutions Frank Stark - Wiesenstrasse 23 - D-75248 Oelbronn-Duerrn / Germany - Telefon +49 (0) 7237-7804 Email: undatec@web.de...
(Limits refer to the switch outputs 1,2 and 3. Switch output 4 is for a different Application allocates. Value is the value at which the selected switching output switches). UNDATEC Flow Measurement Solutions Frank Stark - Wiesenstrasse 23 - D-75248 Oelbronn-Duerrn / Germany - Telefon +49 (0) 7237-7804 Email: undatec@web.de...
Page 11
Function 40: Select the boot loader. Is needed for firmware updates. Function 41: Setting the display brightness UNDATEC Flow Measurement Solutions Frank Stark - Wiesenstrasse 23 - D-75248 Oelbronn-Duerrn / Germany - Telefon +49 (0) 7237-7804 Email: undatec@web.de...
Page 12
5 steps with entering the height cutoff point and the addition in %. Function 99: Displaying Date and Time UNDATEC Flow Measurement Solutions Frank Stark - Wiesenstrasse 23 - D-75248 Oelbronn-Duerrn / Germany - Telefon +49 (0) 7237-7804 Email: undatec@web.de...
Page 13
After taking over in the device software, the SD card can be removed from the device when no data needs to be stored. UNDATEC Flow Measurement Solutions Frank Stark - Wiesenstrasse 23 - D-75248 Oelbronn-Duerrn / Germany - Telefon +49 (0) 7237-7804...
Page 14
400mm safely. An increasing velocity at higher filling levels can not be measured and then calculated with the "Function 98". UNDATEC Flow Measurement Solutions Frank Stark - Wiesenstrasse 23 - D-75248 Oelbronn-Duerrn / Germany - Telefon +49 (0) 7237-7804...
Page 15
The USB interface is neccessary for update the firmware to be made. This requires a connection to a USB cable to a PC. The following figure shows the necessary cable. UNDATEC Flow Measurement Solutions Frank Stark - Wiesenstrasse 23 - D-75248 Oelbronn-Duerrn / Germany - Telefon +49 (0) 7237-7804...
0014.0 l/s 38 m3 With the most spreadsheet programs, it is possible to design curves, graphs, and statistical analysis. UNDATEC Flow Measurement Solutions Frank Stark - Wiesenstrasse 23 - D-75248 Oelbronn-Duerrn / Germany - Telefon +49 (0) 7237-7804 Email: undatec@web.de...
With the screws the bracket must be mounted on the rear panel, the rosettes are not necessary for this (see photo). UNDATEC Flow Measurement Solutions Frank Stark - Wiesenstrasse 23 - D-75248 Oelbronn-Duerrn / Germany - Telefon +49 (0) 7237-7804...
Page 18
To disassemble the device, it is also compressed down and allow the spring, then it can be taken out again. UNDATEC Flow Measurement Solutions Frank Stark - Wiesenstrasse 23 - D-75248 Oelbronn-Duerrn / Germany - Telefon +49 (0) 7237-7804 Email: undatec@web.de...